background image

24

    unigreen

5.6

MARKER

The marker indicates the zone where the treatment has been applied.
It produces a chemical foam that doesn’t damage the crops, which is
deposited on the ground and disappears after roughly an hour. The marker is
an accessory available on request. For the use and maintenance of the
system follow the instructions in the specific handbook in the package or
enclosed with machine manual.
WARNING: the foam liquid is ruined by frost, very hard water can change the
yield and function.

6

HAND LANCES

When using hand lances bear in mind the following notes:

=

Don’t direct the jet of liquid towards electric power lines or zones where

there is electrical current, houses or where people might pass.
= Don’t point the jet at people or animals.
The jet can cause serious injuries simply due to the mechanical force of the
liquid under pressure.

=

Never block the spraying lever of the lance in an open position because if

the lance falls it will be uncontrollable.

=

At the end of work after you have stopped the pump, make sure that any

residual pressure in the pipes under pressure has been drained to avoid
unexpected jets when putting the lance away.
There are various types of lances; with a lever, mitra spray gun and pistol
grip.
For further information please refer to the handbook in the package.
The lever lance is controlled by opening lever A which, depending on how
much it’s pressed, produces a conical spray or direct jet. The standard
nozzle is Ø 1.5
The mitra spray gun can produce a direct jet or a conical spray and the type
of spray is selected by pushing lever B forwards or backwards. Use lever C
to open the jet. The standard nozzle is Ø 2.5
Replacement nozzles are available for all of the lances and the capacities
are indicated in the tables N° 3  e N° 4.

7

HOSE REEL

Available in the following sizes 20-50-100 , with mechanical, electrical and
hydraulic rotation.
To use the system, consult the enclosed handbook as there are significant
differences between each.
After work it is important to block the winding roller to stop the hose
unwinding while you are moving the sprayer.

C

B

A

Marker

Summary of Contents for CALIPSO 11





































Reviews: