background image

page 2

IMPORTANT PRECAUTIONS

To reduce the risk of electrical shock or fire, do not expose this unit rain or 
moisture.

Do not spill water or other liquids  into or on to your unit.

Do not attempt to operate this unit if the power cord has been frayed or 
broken.

Do not attempt to remove or break off the ground prong from the electrical 
cord. This prong is used to reduce the risk of electrical shock and f re in 
case of an internal short.

Disconnect main power before making any type of connection.

Do not remove the cover under any conditions. There are no user 
serviceable parts inside.

Never plug this unit in to a dimmer pack.

Always be sure to mount this unit in an area that will allow proper 
ventilation. Allow about 6” (15cm) between this device and a wall.

Do not attempt to operate this unit, if it becomes damaged.

This unit is intended for indoor use only, use of this product outdoors voids 
all warranties.

During long periods of non-use, disconnect the unit’s main power.

Always mount this unit in a safe and stable manner.

Power cords should be routed so they are not likely to be walked on, 
pinched by items placed upon or against them.

Cleaning -The outside of the unit should be wipe down with a soft cloth and 
mild cleaner when needed.

Heat -The amplifier should be situated away from heat sources such as 
radiators, heat registers, stoves, or other appliances (including amplifiers) 
that produce heat.

The fixture should  be serviced by qualified service personnel when:

A. The power-supply cord or the plug has been damaged.

B. Objects have fallen, or liquid has been spilled into the unit.

C. The appliance has been exposed to rain or water.

D. The fixture does not appear to operate normally or exhibits a 

marked change in performance.

Congratulations and thank you for purchasing NA-3600/NA-5600/NA-8600

 

amplifier. These amplifiers are representation of UNiKA’s continuing 

commitment to produce the best and highest quality audio products at an 

affordable price. These amplifiers are designed to provide a big impact in 

sound reproduction. Please read and understand this manual completely 

before attempting to operate your new amplifier. This booklet contains 

important information concerning the proper and safe operation of your new 

amplifier.

UNPACKING:

 Every NA-3600/NA-5600/NA-8600 amplifier  has been 

thoroughly tested and has been shipped in perfect operating condition. 

Carefully check the shipping carton for damage that may have occurred 

during shipping. If the carton appears to be damaged, carefully inspect your 

unit for any damage and be sure all accessories necessary to operate the 

system have arrived intact. In the event damage has been found or parts are 

missing, please contact your dealer for further instructions.

INSTALLATION:

 These amplifiers are designed to mount into a 

standard 19”rack. The front panel provides four holes used to screw the unit 

into a rack. The unit also provides a way to rear mount the unit into a rack for 

added security. Rear mounting the unit is especially recommended if the 

unit is to mounted into a mobile rack. 

INTRODUCTION

UNiKA

 NA-3600/NA-5600/NA-8600

Important Precautions

Introduction

     

Front Panel     Rear Panels     Set Up     Operating Modes     Protection    Features    Specifications

     

Summary of Contents for NA-3600

















Reviews: