background image

Introduction      Front Panel      

      Set Up      Speakon Assembly      Operating Modes      Protection      Features      Specifications

Rear Panel

page 4

10. Fan Outlet Ports 

- Cooling air enters the amplifier through the front 

grills and exhausts through the fans. Be sure not to block these ports 
when installing the amplifier or other associated equipment. Air must 
flow unimpeded through these ports.

11. Channel 1 Output Jack / 5-Way Binding Post - 

Connect to your 

speakers input jack. Red is positive signal and Black is negative signal. 

12. Channel 2 Output Jack / 5-Way Binding Post - 

Connect to your 

speakers input jack. Red is positive signal and Black is negative signal. 

13. Channel 1 Speakon Output -

 Use pins 1+ and 1- of this 4-pole 

Speakon connector to connect to your speakers input jack.

14. Channel 2 Speakon Output - 

Use pins 1+ and 1- of this 4-pole 

Speakon connector to connect to your speakers input jack.

15. AC POWER Cord

 - Plug this cable into a standard 110V or 220V wall 

outlet. Be sure that the supplied voltage in your area matches the 
amplifiers required voltage. Never plug your amplifier into a wall outlet 
that does not match the required voltage of your amplifier, serious 
damage may occur to your unit.

16. Ground Lift Switch - 

This switch is used to disconnect the internal 

ground signal from the amplifier chassis ground. This may reduce the 
buzz that is caused from an electrical 50Hz/60Hz cycle.

17. Low Frequency Enhanced 100Hz (V-9000 only) - 

This switch 

controls to bass boost the sound output at the frequency 100Hz. 

18. Low Cut 30Hz - 

This switch controls to cut (roll-off) the sound output at 

the frequency below 30Hz. 

V-8000 REAR PANEL

PUSH

PUSH

SENSITIVITY

LIMITER

MODE

FILTER 160Hz

LOW CUT 30Hz

BRIDGE

HIGHPASS

ON

OFF

STEREO

LOWPASS

OFF

ON

PARALLEL

BYPASS

GROUND

K

C

O

L

K

C

O

L

H2

C

H1

C

CH1

CH2

+
+

-

-
+

-

CH1

CH2

BRIDGE

PINOUT

1+

1-

POS NEG

CH 2

PINOUT

2+

2-

POS NEG

CH 2

1+

2+

POS NEG

BRIDGE

1+

1-

POS NEG

CH 1

AC INPUT

~220V  50Hz

OUTPUTS

0.775V

1V

1.44V

Made in Taiwan

Serial No.:

OFF

ON

CH1

CH2

THRU

INPUT

Figure

 

2

16

24

15

12

14

26

25

23

22

20

19

1

3

 

10

1

1

 

21

18

UNiKA

 V-8000/V-9000

Summary of Contents for V-8000

















Reviews: