WIRELESS ROUTER
type
VIT02
Instruction Manual 0
6
-
VIT02
-
02
-
17
Manufacturer
:
UniPOS Ltd.
,
47 San Stefano Street, Pleven 5800, Bulgaria,
http://www.unipos-bg.com
1
2
Fig
.1
3
GENERAL DESCRIPTION
The
router
is designated to expand the range of the Fire Alarm System VIT, transmitting the signals between the fire detectors and the other
routers
or the
Control Panel in the system. Communication between them is based on a high-frequency radio emission. The router has one monitored output for fire
condition, which is intended to control external for the system devices. If the output is assigned to a zone, then on the relative fire phase, the output is
activated and the
router
switches to “Fire condition” Mode.
The
router
consists of power supply unit, attached to a metal frame (
p
os.
3, fig.2
), and a radio module with external antenna (
pos.2, fig.2
), mounted into a
plastic box with base (pos.5, fig.2) and cover (pos.7, fig.2). Under the radio module, on the right side, are located the monitored output terminals, for
connection with external devices (
pos.2, fig.3
).
Built indication, green (pos.1,
fig.
1), yellow (pos
.
2,
fig.
1) and red (pos.3,
fig.1
) LED provides status information to the
router
:
- “
Network Connection” Mode –
R
ed and yellow LEDs are
lights up continuously
. The
router
scans all frequency channels. Upon recognition of a
Control Panel or another
router
, it submits a request for connection to the network
. I
f the request is confirmed, the
router
is registered in the configuration of
the Control Panel and switches to “Service” Mode. The
router
may switch back to ”Network Connection” Mode in case of failed radio connection between it
and another
router
(The Fire Control Panel);
- “
Service” Mode –
G
reen LED, flashing up with different frequency, proportional to the established quality of the connection with the Control Panel or
another
router
. Upon significant attenuation of the radio signal, the green LED changes to red flashing up LED.
This mode checks the quality of the strength
signal between the
router
and the Control Panel or another
router
. From the menu of the panel can be adjusted and reviewed the network parameters of the
router;
- “
Duty” Mode –
G
reen LED lights up continuously. The
router
periodically checks the status of the mains supply and the back up battery supply and
sends the status to the Control Panel
;
- “
Fire condition” Mode –
R
ed LED lights up continuously
and output is activated
. The
router
remains in that condition until it receives a fire restart
command from the Control Panel and deactivates the output;
- “
Fault condition” Mode –
Y
ellow LED lights up continuously. The
router
keeps its network functions, but there exist one of the following fault
conditions, displayed on the screen of the Control Panel:
•
Interrupted mains
or back up battery
supply;
•
Fault condition in output for power supply (24V)
;
•
Fault in monitored output - short circuit or interruption;
- “
Registration” Mode –
O
n the Control Panel is displayed the status of the relative
router
. This mode is autonomous for the
router
and operates in
combination with
“Service” mode
mentioned above. It allows Enable/Disable the registration of new devices through the
router and on the same time set
router in “Service” mode;
TECHNICAL DATA
Supply voltage:
• Mains supply
220/230V (50/60Hz)
• Back up battery
-
Back up battery type
lead, gel electrolyte
-
Nominal voltage/capacity C of the back up battery
12 V/1,2 Ah
20
-
Discharged battery voltage
9 V
DC
-
Charge battery voltage
14 V
DC
-
Consumption on back up battery supply in Duty Mode
< 60mA
peak value at 12 V
Power supply output
1 pc.
+2
•
Voltage
(24 / ) V
DC
-4
•
Maximum current value
4
00 mA
Monitored
output for fire condition:
1 pc.
•
Type
potential
+2
•
Electrical characteristics
(24 / ) V
DC
-4
•
Maximum current value
4
00 mA
Indication of the registered events:
•
Light indication
LED (yellow, green
and red LED)
2
Cross section of the connecting wires
(0,8 – 1,5 ) mm
Response time
30 sec.
Degree of protection
IP50
o
o
Operating temperature range
minus 10 C до 55 C
Relative humidity resistance (no condensation)
≤
95%
Overall dimensions (excluding the antenna) (width / depth /height) 130x170x80 mm
Weight, excluding the back up batteries, not more than
0,400 kg
MOUNTING AND PUT INTO OPERATION
The device is mounted on a wall indoors and the distance from the tip of the antenna to the ceiling must be at least 20 cm.
1. Manufacturer recommendations
1.1
Routers should not be installed in locations distant by more than one barrier (wall) from the Control Panel or another routers. Exceptions to this rule are
permitted in approved working capacity of the team.
1.2.
In premises, where there is other devices operating in the frequency range of 2.4GHz, it is necessary to scan and detect the channel of operation of
these devices. This ensures that the Fire Alarm system we use will occupy a channel that will be shared only by its devices.
2.
E
valuation of the signal strength
Before proceeding to installation of the
router
, the place chosen by the installer needs to be carefully evaluated for the signal strength depending on the
previous
router
or the Control Panel. The “Mainstay” of the wireless fire alarm system is build by the Control panel VIT 01 and
router
VIT 02.
Evaluation of the signal strength of
router
shall be performed as follows:
2.1.
Provide a Control Panel VIT01 or another
router
VIT02, connected to Control Panel VIT01
.
2.2.
Set the device into Mode “Registration” (See Instruction Manual of VIT01)
.
2.3.
Join the antenna.
2.4.
Dismantle the cover (po
s
.7,
fig.2
) from the base (pos.5,
fig.
2) by developing the four screws (pos.1,
fig.
2). Fit the battery (pos.6,
fig.
2) and join the
wires to the terminals thereof. Red wire to (+) and to blue (-) battery.
Yellow
LED
lights
(mains supply). The
router
booster scans all channels. Allow
registration of the
control panel
.
2.5.
An assessment of the patency of the signal in the "Service" of the
router
to the installation site without the device is permanently mounted on the
wall. This allows, if necessary, to choose a suitable place for installation.
