h) Clean the device regularly to avoid a durable
encrustation of dirt.
i)
The device is not a toy. Cleaning and maintenance
may not be carried out by children without
supervision by an adult person.
j)
The time of continuous heating or filtering of
water should not exceed 48 hours.
k)
For health reasons, it is necessary to clean and
exchange water in jacuzzi regularly.
l)
The product may be slippery, which may cause
falls.
m) It is forbidden to start the product if the suction
parts are damaged. The suction fittings should
be replaced only with exactly the same type of
parts, it is forbidden to use parts with different
parameters.
n)
After each use, secure the product with a lid to
avoid accidental falling into the water.
o) Regularly check the condition of the lid. It is
forbidden to use a damaged cover.
p)
It is forbidden to switch the device on if it is likely
that the water is frozen or heavily polluted.
q) NOTE: To speed up the heating process it is
acceptable to turn on the heating while the cover
is on the device. Do not turn on the filter system
and/or air bubbles when the cover is on the
device.
r)
Ensure that animals are not able to enter the
product.
s)
The water in the jacuzzi during the bath should
not exceed 40°C. A temperature between 38 and
40°C is considered safe for a healthy adult. For
children and when using the device for more than
10 minutes, set the water temperature to a lower
level.
t)
It is forbidden to start the pump if the water is
below the minimum level, as it will damage the
pump.
ATTENTION!
Despite the safe design of the
device and its protection facilities and despite
the use of additional elements protecting the
operator, there is still a slight risk of an accident
or injury when using the device. When using the
device stay alert and use common sense.
3. USE GUIDELINES
The device is designed for a relaxing bath in water with
the possibility of heating the water and massage with
air bubbles. The product is intended for home use only!
The user is liable for any damage resulting from
nonintended use of the device.
3.1. DEVICE DESCRIPTION
1.
Control panel
2.
Swimming pool
3. Cover
4. Hose
5. Filter
6.
Filter cover
7.
Repair Kit
8. Tarpaulin
1
2
5
3
4
6
7
8
2.4. SAFE DEVICE USE
a)
Do not use the device if the ON/OFF switch does
not function properly (does not switch the device
on and off). Devices which cannot be switched on
and off using the ON/OFF switch are hazardous,
should not be operated and have to be repaired.
b)
When not in use, store in a safe place, away from
children and people not familiar with the device,
who have not read the user manual. The device may
pose a hazard in the hands of inexperienced users.
c)
Maintain the device in a good technical state.
Before each use check for general damage and
especially check for cracked parts or elements
and for any other conditions which may impact
the safe operation of the device. If damage is
discovered, hand over the device for repair before
use.
d)
Device repair or maintenance should be carried
out by qualified persons, only using original spare
parts. This will ensure safe use.
e)
To ensure the operational integrity of the device,
do not remove factory fitted guards and do not
loosen any screws.
f)
Do not touch articulated parts or accessories,
unless the device has been disconnected from
a power source.
g)
It is forbidden to move, adjusting and rotating the
device in the course of work.
u)
The product is subject to the rules for swimming
pool fencing, please consult your local authorities.
v)
Use in areas free of obstacles and sharp objects.
w) It is forbidden to place the product in another
water tank.
x)
Place the product only on a surface that will
withstand its weight when filled with water and
the weight of users.
y)
Never add water to chemicals that clean water,
always add chemicals to water. Adding water to
chemicals will cause them to atomise and lead to
strong chemical reactions.
z)
The device cannot be used at a temperature
below 4°C.
aa) It is not recommended to expose the product to
long-lasting sunlight.
bb) It is forbidden to add bath salts, fragrance oils,
cleansing liquids, etc. to the water.
cc) Do not pour water above 40°C into the device.
dd) It is forbidden to move the pool along the ground
surface. In order to transport the device for a short
distance, disconnect it from the power supply and
then carry it with two people holding the handles
to the right place.
ee) Do not carry a pool filled with water.
•
Open the air valve and attach the other end of the
hose to the valve.
•
Connect the device to the power supply.
•
Press the On/Off bubble button on the control
panel. Wait for the pool to inflate, taking care not
to exceed the maximum air filling.
•
Press the On/Off bubble button to stop the filling
process.
•
Unscrew the hose from the outlet and air valve,
close the inlet and close the valve.
•
Screw the filter to the pool wall by turning it
clockwise.
•
Fill the pool with water to a point between the
maximum and the minimum level.
•
Cover the jacuzzi pool with a cover.
PLEASE NOTE:
If you want to pump up the water-filled
pool, turn the nozzles on for 2-3 minutes by pressing the
On/Off button for the bubbles and remove the air filter,
and then follow the steps described above.
CONTROL PANEL DESCRIPTION
A.
Temperature increase button
B.
Filtering system On/Off button
C.
Air bubbles On/Off button
D.
Heating water On/Off button
E.
Temperature decrease button
F.
Entry button in temperature settings
G. Display
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher
than 40°C and the relative humidity should be less than
85%. Keep the device away from hot surfaces. Operate
the device on flat, stable, clean, refractory and dry
surfaces out of the reach of children and people with
mental disabilities. The surface should be free of dirt
and sharp edges, and able to resist the weight of the
mass of the device filled with water and users. The area
around the device should have drainage in order to
easily drain the spilled water. The surface around the
device should be slip-resistant.
Always place the device on properly unfolded tarpaulin.
When installing the device inside a building, additional
requirements should be met, i.e.:
•
no hazards due to increased humidity in the
room,
•
ensure adequate ventilation,
•
the floor must withstand the weight of the device
with water and users,
•
it is not recommended to install the device on
upper floors because of the risk of flooding the
rooms below with water,
A
B
F
G
C
E
D
FILTER
BUBBLE
HEATER
TEMPERATURE
For informational purposes only:
Ambient temperature and initial water temperature
are the factors for heating duration. Current water
temperature will be displayed after filter system has been
running for at least one minute.
Ambient
Temperature
Water
Temperature
Set
Temperature
Heating
Duration
50°F (10°C)
50°F (10°C)
104°F (40°C)
23h
59°F (15°C)
59°F (15°C)
104°F (40°C)
18h
68°F (20°C)
68°F (20°C)
104°F (40°C)
14h
77°F (25°C)
77°F (25°C)
104°F (40°C)
11h
86°F (30°C)
86°F (30°C)
104°F (40°C)
8h
•
the drainage of water to the sewage system
should be ensured,
•
it is forbidden to place the device on rugs or other
materials susceptible to moisture.
The power cord connected to the appliance must be
properly grounded and correspond to the technical
details!
INSTALLING THE APPLIANCE
•
Take the product out of the packaging. Spread it
out and make sure that the pool and cover are
right-side up.
•
Open the air outlet from the pool and screw on
one of the hose ends.
EN 13
12
EN
23.05.2022
