•
Remove the filter cover.
•
The filter should be rinsed with water, e.g. from
a garden hose, and it can be re-installed in the
device. If the filter is discoloured or has dirt that
cannot be removed, replace it with a new one.
•
Put the cover on the filter.
•
Screw the filter to the pool wall.
Draining the water
•
Disconnect the device from the power supply.
•
Make sure that the hole in the floor on the inside
of the pool is closed.
•
Open the water outlet on the outside of the pool.
Connect one end of the hose.
•
Open the hole plug on the inside of the pool, the
water will flow out through the hose.
3.3. DEVICE USE
Powering the device
The device is equipped with a power cord with
a residual-current device (circuit breaker). The circuit
breaker should be tested regularly. For this purpose,
reset the switch by pressing the Reset button. Start any
of the jacuzzi functions, e.g. air bubbles, and then press
the TEST button. The switch should cut off the power
supply from the device. Press the RESET button again to
return to the normal operating mode.
PLEASE NOTE: If, after pressing the TEST button, the
switch does not cut off the power supply from the
device, immediately stop using the jacuzzi and contact
the manufacturer‘s service department.
Water filtration function
•
Press the filtration On/Off button. The device will
begin to filter, the diode will light on the button.
•
Pressing the filtration On/Off button again will
turn off the filtering process, the LED on the
button will go off.
•
When the filter pump runtime exceeds 168 hours,
„FC“ will appear on the display and a signal will
be displayed. This will be information about the
need to replace or clean the filter. The LED on the
filter button will be lit, but the filtering itself will
be turned off. Other device systems will also not
work. To turn off the message, press the filtration
On/Off button, the current water temperature
will appear on the display. To restore the filtration
system activity, replace or clean the filter.
Massage function with air bubbles
•
Press the On/Off button for the air bubbles. The
device will start to spray air into the water in front
of the nozzles, the diode will light on the button.
•
Do not activate the function if a cover is placed
on the pool.
•
Pressing the bubbles On/Off button again will
turn off the bubble release process, the LED on
the button will go off.
•
The nozzle system automatically stops working
after 20 minutes. To restart the function, wait 10
minutes.
•
For the first 15 minutes of the function it can be
turned off and turned on without interruption.
After the time of 15 minutes has elapsed after
switching off the air bubble function, wait 10
minutes before turning it on again.
Water heating function
•
Press the On/Off button to heat the water. The
device will start to heat up the water, the diode
will light on the button. It will also light up the
diode on the filtering On/Off button. The device
will also start filtering the water.
•
After reaching the set water temperature
(temperature setting is described in the following
point) + 1
°
C, the heating will be automatically
switched off, but the filtering will continue to
function. The control diodes for heating and
filtering will light up constantly, even after the set
water temperature has been reached.
•
If the water temperature drops 2°C below the set
value, the heating system switches on again (the
filter will continue to run).
•
During the warming process, pressing the
warming button again will switch off the warming
function and its control diode, but filtering will
continue to work for 2 minutes and during this
time the control diode for filtering will light up in
pulses.
Setting the water temperature
•
Press the entry button to set the temperature, the
display will flash.
•
Use the buttons to increase or decrease the
temperature value to set the preferred value.
•
Press the input button again to set the
temperature to confirm the entered value.
1.
The water heating process depends on
the initial water temperature and external
conditions and it takes around 12-24h.
For a water with temperature of 15°C (tap
water), in ideal conditions, heating time will
take 15h to increase the water temperature
up to 30°C.
2.
The heater is mainly used to maintain the
water temperature, we recommend filling
the jacuzzi with warm water.
3.
The product with clear signs of use, water or
dirt residues is not subject to return.
•
After draining all the water, activate the air
bubbles release function for about 2-3 minutes to
get rid of water from the tubes in the device.
•
When finished, disconnect the hose and close the
holes with the plugs.
Storage
•
Completely drain the pool water. Remove the
filter.
•
After draining the water, dry the pool with a dry
cloth and leave it to dry for 24 hours until it is
completely dry.
•
Release the air from the pool by opening the
outlet and air valve, then fold it into the box.
Using the repair kit
•
If the product gets torn or breaks, use the
provided repair kit.
•
Clean and dry the area of damage. Cut out the
patch.
•
Apply the adhesive to the patch, then gently
fasten it to the damaged area.
•
Smooth the surface to remove air bubbles.
3.4. CLEANING AND MAINTENANCE
a) Before each cleaning, adjustment, replacement
of accessories and if the device is not used, it is
necessary to pull out the mains plug.
b)
Use cleaners without corrosive substances to clean
each surface.
c)
Contaminants may be deposited on the walls of the
pool. To clean them, use a mild soap and water.
d)
After cleaning the device, all parts should be dried
before reusing it.
e)
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
f)
Regular inspections of the device must be carried out
in terms of its technical efficiency and any damages.
g)
Use a soft cloth for cleaning.
Keeping water clean
•
In order to keep the device in good condition and
not to expose yourself and other users to health
problems, you should regularly clean the water in
the pool.
•
Water should be periodically cleaned with
chemicals or replaced with fresh water. It is
forbidden to use chemicals with calcium ions.
•
When using chemicals, follow the
manufacturer‘s recommendations and
instructions for use, and consult with local
authorities regarding the permissible use of these
products
•
Replace and clean the filter regularly. It is
recommended to clean the filter after every 72-
120 h of use. The filter should be replaced once
a month depending on the intensity of use.
•
The pH of the water should be maintained at 7.2-
7.8, total alkalinity between 80 and 120 ppm, free
chlorine between 3 and 5 ppm. It is recommended
to use special tests to check the water status.
Tests should be used in accordance with the
recommendations and instructions of their
manufacturer.
Cleaning the filter
•
Disconnect the device from the power supply
•
Unscrew the filter from the pool wall.
EN 15
14
EN
23.05.2022
CAUTION:
After the first pumping, it is natural
that the material may stretch. Reinflation is
needed to get the correct pressure.
