background image

  

13 

 

7. Camera accessories 

 
7.1 Power Supply and Power Cable  
 

12 V DC regulated power supply with 1A current output or better is recommended.  This camera 

uses Hirose 12-pin connector for power source.  The matting cable plug connector can be 
purchased through distributors or UNIQ and the Hirose part number is HR10A10P12S.  UNIQ 
provides power supplies and power cables as "one stop shopping" for customers.  Alternatively, the 

power supplies and power cables can be purchased through power supply and cable vendors.  
Contact UNIQ for vendor list. 

 

7.2 Lens 

C-mount lens is the standard lens for UP-1830CL-12B camera. There are a variety of C-mount 

lenses in the market that works with UP-1830CL-12B camera.  Make sure the quality and 
specification of the lens match the camera's application. Some of the most popular lenses in the 
market, such as Cosmicar, Fujinon, Rodenstock, and Schneider, are recommended. 

 

 
7.3 Camera Link Cable 

 
Camera Link cable can be purchased from 3M, Mouser, Digi-Key and frame grabber vendors.

 

 

 

8. Technical Support Information

 

 
For technical assistance, contact UNIQ Technical Support or Applications Engineer at  
 

Phone:  

 

(408) 330-0818  

Fax:   

 

(408) 330-0886 

Email:  

 

info@uniqvision.com

 

 

Company contact information: 

 

UNIQ VISION, INC. 
2924 Scott Blvd. 
Santa Clara, CA 95054 

 
Phone:  

 

(408) 330-0818 

Fax:   

 

(408) 330-0886 

 
Our website:   

www.uniqvision.com

 

General Inquiries: 

info@uniqvision.com

 

Summary of Contents for UP-1830CL-12B















Reviews: