background image

              

Manager Mode    

The following parameters may be changed using the previous keys:

Parameters  Lowest

  Value

 Highest

   Value

Option 1

Option 2

Default

Value

Meaning

UNITS

---

---

English

Metric

English

English= units of lbs.,
miles, hours, minutes

Metric= units of kg.,
km, hours, minutes.

MN SPD

0.1

2.5

English=0.5

Metric=1.0

0.5

Minimum speed in

MPH or KM/HR

MX SPD

5.0

20.0

English=10.0

Metric=20.0

10.0

Maximum speed in

MPH or KM/HR

EL OPT

---

---

ON

OFF

ON

Turns the elevation

system ON or OFF.

TIME

5

99

99

Maximum time in

minutes allowed for

program, including

warm-up/cool-down.

OP HRS

0

0

---

---

6,553.5

Total operating hours

DIST

0

0

---

---

65,635

Total treadmill miles

(Units=English)

or kilometers

(Units=Metric)

WEIGHT

0

399

---

---

155

Defaults (to user),

typical weight in lbs/kg

depending on what

setting (UNITS=

English or Metric

SER NO

0

0

---

---

65,535

Treadmill serial

number.

LANG

---

---

---

---

English

Language in English,

Dutch, German,

Portuguese, Spanish,

Swedish, or Italian.

ENTRY

---

---

Units

Tenths

Units

This variable changes

the starting speed in

Units or Tenths

3.2

Summary of Contents for Star Trac 4500











Reviews: