background image

10

GETTING STARTED

u

npacking

 

a

 

new

 

sensor

When receiving a new microsensor remove the shock-absorbing 
grey plastic net . 

Please do not remove the seal and protective 

tube before the following steps are successfully completed.

c

onnecT

 

The

 

TemperaTure

 

sensor

 

Connect the Unisense temperature microsensor to the input 
terminal of the T301 or the Microsensor Multimeter or Monometer . 

c

alibraTion

Without calibration, the Unisense temperature sensor in 
combination with the Unisense T301 thermometer has a precision 
of ±1

o

C . To verify the function and/or to achieve an even better 

precision (down to ±0 .1 

o

C), perform the following calibration 

procedure: Prepare two solutions with well defined temperature, 
one slightly above and one slightly below the temperature range 
in which the measurements are expected to be performed . 
To ensure that the calibration temperatures are well-defined, 
use for instance boiling water versus ice-water, or monitor the 
temperature of the solutions with an independent thermometer 
with a better precision than 1

o

C . 

Microsensor Multimeter/Monometer: Perform the calibrations in 
the software . Please consult the relevant software manual . 

T301: If the display of the T301 deviates from the independent 
thermometer, you can correct subsequent measurements by 
adding the difference to the display value .
 

WARNING

Do not remove 

seal and protective 

plastic tube before 

the following steps  

are successfully 

completed.

The Unisense T301 thermocouple 

meter which is used for the TP-MR and 

TP200 temperature microsensors.

Summary of Contents for TP-MR

















Reviews: