background image

035-19656-003 Rev. A (1004)

Unitary Products Group

23

Example: For a 130,000 BTUH (38.06 kW) furnace with 2 return open-
ings and operating on high-speed blower, it is found that total system
static is 0.58” w.c. To determine the system airflow, complete the follow-
ing steps:
Obtain the airflow values at 0.50 w.c. (125 Pa) & 0.60 w.c. (150 Pa)
ESP.

Airflow @ 0.50”: 2125 CFM (60.17 m

3

/min)

Airflow @ 0.60”: 2035 CFM (57.62 m

3

/min)

Subtract the airflow @ 0.50 w.c. (125 Pa) from the airflow @ 0.60 w.c.
(150 Pa) to obtain airflow difference.

2035 - 2125 = -90 CFM (2.55 m

3

/min)

Subtract the total system static from 0.50 w.c. (125 Pa) and divide this
difference by the difference in ESP values in the table, 0.60 w.c.
(150 Pa) - 0.50 w.c. (125 Pa), to obtain a percentage.
(0.58 - 0.50) / (0.60 - 0.50) = 0.8
Multiply percentage by airflow difference to obtain airflow reduction.
(0.8) X (-90) = -72
Subtract airflow reduction value to airflow @ 0.50 w.c. (125 Pa) to
obtain actual airflow @ 0.58 inwc (144 Pa) ESP.
2125 - 72 = 2053

NOTES

1. Airflow expressed in standard cubic feet per minute (CFM) and in cubic meters per minute (m

3

/min).

2. Motor voltage at 115 V.

* Input / CFM / Cabinet Width (A=14-1/2, B=17-1/2, C=21, D=24-1/2)

† Indicates model available in LoNOx.

TABLE 17: 

Blower Performance CFM - Upflow (without filter) - Bottom Return

MODELS

Input / 

CFM

Speed

Single Stage Bottom Airflow Data (SCFM) 

Single Stage Bottom Airflow Data (cm/m) 

Ext. Static Pressure (in. H2O) 

Ext. Static Pressure (kPa)

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0  0.025 

0.050 

0.075 

0.100 

0.125 

0.149 

0.174 

0.199 

0.224 

0.249 

40/1200/A 

High 

1610 1540 1460 1360 1290 1200 1110 1020 900  760  45.6 43.6 41.3 38.5 36.5 34.0 31.4 28.9 25.5 21.5 

Medium 

High 1430 1390 1330 1250 1190 1110 1030 940  840  710  40.5 39.4 37.7 35.4 33.7 31.4 29.2 26.6 23.8 20.1 

Medium 

Low 1200 1180 1140 1100 1050 1000 930  850  750  620  34.0 33.4 32.3 31.1 29.7 28.3 26.3 24.1 21.2 17.6 

Low 

980 980 960 920 890 840 790 720 620 530  27.8 27.8 27.2 26.1 25.2 23.8 22.4 20.4 17.6 15.0 

60/1200/A 

High 

1570 1490 1420 1340 1250 1180 1090 990  870  700  44.5 42.2 40.2 37.9 35.4 33.4 30.9 28.0 24.6 19.8 

Medium 

High 1410 1360 1310 1250 1190 1090 1020 920  810  650  39.9 38.5 37.1 35.4 33.7 30.9 28.9 26.1 22.9 18.4 

Medium 

Low 1200 1180 1150 1100 1050 990  920  830  700  580  34.0 33.4 32.6 31.1 29.7 28.0 26.1 23.5 19.8 16.4 

Low 

960 960 950 930 900 840 800 720 610 500  27.2 27.2 26.9 26.3 25.5 23.8 22.7 20.4 17.3 14.2 

80/1200/A 

High 

1590 1520 1460 1380 1300 1240 1150 1050 930  800  45.0 43.0 41.3 39.1 36.8 35.1 32.6 29.7 26.3 22.7 

Medium 

High 1400 1360 1310 1260 1200 1140 1070 960  860  740  39.6 38.5 37.1 35.7 34.0 32.3 30.3 27.2 24.4 21.0 

Medium 

Low 1180 1160 1130 1090 1040 990  920  840  750  640  33.4 32.8 32.0 30.9 29.4 28.0 26.1 23.8 21.2 18.1 

Low 

940 940 940 920 880 840 790 710 630 530  26.6 26.6 26.6 26.1 24.9 23.8 22.4 20.1 17.8 15.0 

80/1600/B 

High 

1850 1820 1790 1750 1690 1630 1570 1500 1430 1330  52.4  51.5  50.7  49.6  47.9  46.2  44.5  42.5  40.5  37.7 

Medium 

1470 1450 1440 1430 1390 1360 1310 1270 1220 1150  41.6  41.1  40.8  40.5  39.4  38.5  37.1  36.0  34.5  32.6 

Low 

1260 1260 1260 1260 1250 1200 1150  1110 1070 1010  35.7  35.7  35.7  35.7  35.4  34.0  32.6  31.4  30.3  28.6 

80/2200/C 

High 

2490 2410 2320 2230 2130 2030 1900 1790 1630 1470  70.5  68.2  65.7  63.1  60.3  57.5  53.8  50.7  46.2  41.6 

Medium High 2120 2060 2000 1970 1840 1730 1680 1570 1460 1260  60.0  58.3  56.6  55.8  52.1  49.0  47.6  44.5  41.3  35.7 

Medium Low  1720 1700 1670 1620 1570 1500 1430 1310 1160 1000  48.7  48.1  47.3  45.9  44.5  42.5  40.5  37.1  32.8  28.3 

Low 

1410 1390 1360 1330 1280 1220 1170 1060 930  840  39.9 39.4 38.5 37.7 36.2 34.5 33.1 30.0 26.3 23.8 

100/1200/B 

High 

1700 1620 1560 1480 1390 1300 1210 1110 970  820  48.1 45.9 44.2 41.9 39.4 36.8 34.3 31.4 27.5 23.2 

Medium 

High 1430 1400 1350 1300 1230 1160 1080 980  870  710  40.5 39.6 38.2 36.8 34.8 32.8 30.6 27.8 24.6 20.1 

Medium 

Low 1180 1170 1160 1130 1080 1030 1000 860  750  510  33.4 33.1 32.8 32.0 30.6 29.2 28.3 24.4 21.2 14.4 

Low 

950 950 930 920 880 840 790 720 620 530  26.9 26.9 26.3 26.1 24.9 23.8 22.4 20.4 17.6 15.0 

100/1600/B 

High 

1880 1850 1770 1720 1650 1560 1490 1420 1320 1210  53.2  52.4  50.1  48.7  46.7  44.2  42.2  40.2  37.4  34.3 

Medium  1470 1460 1420 1390 1360 1300 1250 1190 1110 1000  41.6 41.3 40.2 39.4 38.5 36.8 35.4 33.7 31.4 28.3 

Low 

1250 1240 1220 1190 1150 1130 1070 1030 970  880  35.4 35.1 34.5 33.7 32.6 32.0 30.3 29.2 27.5 24.9 

100/2000/C 

High 

2590 2500 2400 2280 2180 2080 1970 1840 1720 1560  73.3  70.8  68.0  64.6  61.7  58.9  55.8  52.1  48.7  44.2 

Medium High 2180 2120 2040 1980 1900 1810 1720 1600 1480 1320  61.7  60.0  57.8  56.1  53.8  51.3  48.7  45.3  41.9  37.4 

Medium Low  1750 1720 1680 1640 1580 1520 1440 1350 1220 1060  49.6  48.7  47.6  46.4  44.7  43.0  40.8  38.2  34.5  30.0 

Low 

1450 1420 1380 1330 1300 1240 1160 1070 970  860  41.1 40.2 39.1 37.7 36.8 35.1 32.8 30.3 27.5 24.4 

115/1600/C 

High 

2020 1930 1820 1730 1640 1540 1400 1250 1090  920 

57.2  54.7  51.5  49.0  46.4  43.6  39.6  35.4  30.9  26.1 

Medium  1750 1710 1650 1590 1490 1390 1290 1160 1010 810  49.6 48.4 46.7 45.0 42.2 39.4 36.5 32.8 28.6 22.9 

Low 

1540 1500 1460 1410 1350 1260 1180 1060 910  750  43.6 42.5 41.3 39.9 38.2 35.7 33.4 30.0 25.8 21.2 

115/2000/C 

High 

2500 2400 2320 2220 2110 2000 1870 1750 1610 1450  70.8  68.0  65.7  62.9  59.7  56.6  53.0  49.6  45.6  41.1 

Medium High 2130 2070 1990 1920 1840 1760 1660 1570 1460 1320  60.3  58.6  56.4  54.4  52.1  49.8  47.0  44.5  41.3  37.4 

Medium Low  1700 1680 1650 1620 1560 1500 1410 1320 1210 1070  48.1  47.6  46.7  45.9  44.2  42.5  39.9  37.4  34.3  30.3 

Low 

1420 1390 1360 1330 1290 1240 1150 1060 950  840  40.2 39.4 38.5 37.7 36.5 35.1 32.6 30.0 26.9 23.8 

130/2000/D 

High 

2640 2550 2440 2340 2230 2110 2010 1870 1750 1580  74.8  72.2  69.1  66.3  63.1  59.7  56.9  53.0  49.6  44.7 

Medium High 2120 2070 2010 1950 1890 1810 1730 1610 1490 1320  60.0  58.6  56.9  55.2  53.5  51.3  49.0  45.6  42.2  37.4 

Medium Low  1690 1660 1640 1600 1550 1490 1410 1330 1240 1100  47.9  47.0  46.4  45.3  43.9  42.2  39.9  37.7  35.1  31.1 

Low 

1370 1360 1340 1310 1270 1230 1150 1070 990  850  38.8 38.5 37.9 37.1 36.0 34.8 32.6 30.3 28.0 24.1 

Summary of Contents for PS8





























Reviews: