CS Unitec Model CSR-150
20” Walk-Behind Pneumatic Concrete Saw
Congratulations on your purchase. We consider the CS Unitec
Model CSR-150 20” pneumatic concrete saw to be among the finest
concrete saws in the world. It has been engineered to withstand the
construction environment and will last many years with the proper
care and maintenance.
The heart of the CSR-150 is a newly developed pneumatic motor coupled
with a heavy-duty gear drive. Our motor runs at a higher speed than most
conventional saws and attains its amazing horsepower from this optimum
speed. The gear drive then reduces the speed attaining the maximum
horsepower.
FIRST AND FOREMOST:
The use of blades, oil, and replacement parts other than those supplied by
CS Unitec may compromise your saw’s performance, operator safety, and
also lead to higher-than-normal maintenance and repair requirements.
ADDITIONALLY:
1. Pneumatic tool lubrication is critical to achieving the maximum
performance and life from your pneumatic tool. We strongly suggest
lubrication through the air inlet. When using an in-line oiler, install it
as close to the motor as possible. One drop of oil per minute is
adequate lubrication for most pneumatic motors.
2. It is also recommended that, when the saw is going to be shut down at
the end of the day, the air line be shut off and the saw disconnected.
Pour approximately 1/2 oz. of CS Unitec Air Tool Lubricant into the
line, then reconnect the line to the saw and give the throttle about a 2-
second burst. This procedure will coat the internal parts of the motor
displacing any moisture and will prevent any rust or corrosion.
3. All CS Unitec pneumatic tools should be operated and maintained in
accordance with American National Standards Institute Safety Code
for Portable Air Tools (ANSI B186.1) and any other applicable safety
codes and regulations. B186.1 information is available from the
National Standards Institute, Inc., 11 West 42
nd
Street, New York, NY
10036.
CS Unitec, Inc.
22 Harbor Ave., Norwalk CT 06850
Phone (800) 700-5919 or (203) 853-9522
♦
Fax (203) 853-9921
Website: http:/www.csunitec.com
♦
e-mail: info@csunitec.com
- 1 -
CS Unitec Model CSR-150
20” Walk-Behind Pneumatic Concrete Saw
Congratulations on your purchase. We consider the CS Unitec
Model CSR-150 20” pneumatic concrete saw to be among the finest
concrete saws in the world. It has been engineered to withstand the
construction environment and will last many years with the proper
care and maintenance.
The heart of the CSR-150 is a newly developed pneumatic motor coupled
with a heavy-duty gear drive. Our motor runs at a higher speed than most
conventional saws and attains its amazing horsepower from this optimum
speed. The gear drive then reduces the speed attaining the maximum
horsepower.
FIRST AND FOREMOST:
The use of blades, oil, and replacement parts other than those supplied by
CS Unitec may compromise your saw’s performance, operator safety, and
also lead to higher-than-normal maintenance and repair requirements.
ADDITIONALLY:
1. Pneumatic tool lubrication is critical to achieving the maximum
performance and life from your pneumatic tool. We strongly suggest
lubrication through the air inlet. When using an in-line oiler, install it
as close to the motor as possible. One drop of oil per minute is
adequate lubrication for most pneumatic motors.
2. It is also recommended that, when the saw is going to be shut down at
the end of the day, the air line be shut off and the saw disconnected.
Pour approximately 1/2 oz. of CS Unitec Air Tool Lubricant into the
line, then reconnect the line to the saw and give the throttle about a 2-
second burst. This procedure will coat the internal parts of the motor
displacing any moisture and will prevent any rust or corrosion.
3. All CS Unitec pneumatic tools should be operated and maintained in
accordance with American National Standards Institute Safety Code
for Portable Air Tools (ANSI B186.1) and any other applicable safety
codes and regulations. B186.1 information is available from the
National Standards Institute, Inc., 11 West 42
nd
Street, New York, NY
10036.
CS Unitec, Inc.
22 Harbor Ave., Norwalk CT 06850
Phone (800) 700-5919 or (203) 853-9522
♦
Fax (203) 853-9921
Website: http:/www.csunitec.com
♦
e-mail: info@csunitec.com
- 1 -
