Unitech MS282 User Manual Download

Page: 66 / 169

- 49 -

unitech is a registered trademark of unitech Electronics Co., Ltd.

MS282 User’s Manual

3.3.21 EAN/JAN Zero Extend

Scan

Enable EAN/JAN Zero Extend

to add five leading zeros to decoded

EAN-8 symbols to make them compatible in length to EAN-13 symbols.
Scan

Disable EAN/JAN Zero Extend

to transmit EAN-8 symbols as is.

Enable EAN/JAN Zero Extend

Disable EAN/JAN Zero Extend*

3.3.22 UCC Coupon Extended Code

Scan

Enable UCC Coupon Extended Code

to decode UPC-A bar codes

starting with digit ‘5’, EAN-13 bar codes starting with digit ‘99’, and
UPC-A/GS1-128 coupon codes. UPC-A, EAN-13, and GS1-128 must be
enabled to use this feature.

Enable UCC Coupon Extended Code

Disable UCC Coupon Extended Code*

Summary of Contents for MS282


























































































































































Search results

Summary of Contents for MS282

Reviews:

Related manuals for MS282

Brands by name

Popular brands

Unitech MS282, User Manual

Search results

Summary of Contents for MS282

Reviews:

Related manuals for MS282

Brands by name

Popular brands