background image

UNITED FIRE SYSTEMS 

STANDPIPE-

PAC™ MODEL SSS-101 

DESIGN, INSTALLATION, OPERATION, AND MAINTENANCE MANUAL 

REVISION 2.00 

P/N 10-540101-001 

 

Page 33 

 

4.4.5.  To Refill Standpipe With Air Pressure After Fire Department Use 
 
 
 
 
 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 

 

Operate Compressor Disconnect Switch to OFF. 

 

Close 

STANDPIPE-

PAC™

 outlet valve. 

 

Use standpipe main drain valve to completely drain standpipe with water. 

 

Use  Auxiliary  Condensate  Drain  Device  to  completely  drain  piping  in  the  vicinity  of  the 

STANDPIPE-

PAC™ 

of water. 

 

It  may  take  time  for  all  water  to  migrate  to  drains  from  upper  floors.  DO  NOT  proceed  until  all  water  is 
drained. 

 

Ensure all standpipe valves and drains are CLOSED. 

 

Operate Compressor Disconnect Switch to ON. 

 

STANDPIPE-

PAC™ 

unit will fill standpipe with air. 

 

TO REFILL STANDPIPE WITH AIR PRESSURE 

INDICATOR or CONTROL 

ITEM 

STATUS 

Visual Indicator 

Pressure Gauge 

Indicating less than 7 PSIG 

Visual Indicator 

AC POWER 

ON 

Visual Indicator 

ACTIVE 

ON 

Visual Indicator 

COMM. FAIL 

Off 

Visual Indicator 

BATT. FAULT 

Off 

Visual Indicator 

SYSTEM TRBL 

Off 

Visual Indicator 

SUPERVISORY 

Off 

Visual Indicator 

GND FAULT 

Off 

Audible Indicator 

Piezo Sounder 

ON 

Audible Indicator 

Signal Horn 

ON 

Control 

Lockable Shutoff Valve 

Open 

Control 

Compressor Disconnect Switch 

ON 

Control 

Test / Service Device 

Not Operated 

 
 
 
 
 
 
 

 

CAUTION  

After standpipe-has been filled with water for any reason, ensure that standpipe is completely empty of water 

before refilling standpipe with air pressure.  Use all available drain points to remove all water from the 

standpipe.  If, at any time, it is suspected that water has entered the 

STANDPIPE-

PAC™

 unit, contact UNITED 

Fire Systems or your trained distributor before refilling standpipe with air pressure. 

 

CAUTION  

If fire department used standpipe during cold weather: 

 

Drain standpipe before freezing occurs 

 

If freezing does occur, ensure all ice within standpipe is melted, and all liquid water is drained 

 

Summary of Contents for STANDPIPE-PAC SSS-101




































































Reviews: