background image

HEX

ADJUSTMENT

SCREW

MAIN ADJUSTMENT

WHEEL

4-1/4"

5-1/8"

LOCKING SCREW

1/2" NPT

COM

AB

GROUND

SCREW

(GREEN)

SWITCH #2

D770-17-00 

1 I56-0986-008R

EPS40 Series and EPS120 Series 
Supervisory Pressure Switches

INSTALLATION AND MAINTENANCE INSTRUCTIONS

 3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

www.systemsensor.com

IMPORTANT

Please Read Carefully and Save

This instruction manual contains important information about the installa-
tion and operation of supervisory pressure switches. Purchasers who install 
switches for use by others must leave this manual or a copy of it with the user.

Read all instructions carefully before installation, following only those instruc-
tions that apply to the model you are installing.

Before installing any alarm device, be thoroughly familiar with:

NFPA 72:  National Fire Alarm Code
NFPA 13:  Installation of Sprinkler Systems
NFPA 25:   Inspection, Testing, and Maintenance of Water-based Fire Protec-

tion Systems

NFPA 13D:  Standard for 1 and 2 Family Dwellings and Manufactured Homes
NFPA 13R:  Standard for Multi-family Dwellings

Other applicable NFPA standards, local codes, and the requirements of the 
authority having jurisdiction.

Failure to follow these directions may result in failure of the device to report 
an alarm condition. System Sensor is not responsible for devices that have 
been improperly installed, tested, or maintained.

CAUTION

Do not use in potentially explosive atmospheres.Do not leave unused wires exposed.

OPERATION

As pressure changes, a diaphragm actuates 1 or 2 snap action switches. The 
pressure switch actuation is determined by adjustment settings.

INSTALLATION

1.  Remove Cover
 

Cover is held on by two screws. 

2.  Mounting the Switch
 

 The device is designed to be mounted in the upright position; side mounting 
is also acceptable. Locate it where vibration, shock, and mechanical loading 
are minimal. Refer to piping diagram above (Fig. 2 and 3).

 

a.   Mount the device directly to the line via the 

1

2

" NPT pressure con-

nection. The use of teflon pipe sealant tape is recommended. Be sure 
the fitting is tight enough to prevent leaks.

 

b.  Apply tightening torque to the black plastic hex portion of the device.

SPECIFICATIONS

Contact Ratings: 

10 A, 1/2 HP @ 125/250 VAC 

 

8A @ 125/250 VAC ~ (LPCB ONLY)

 

2.5A @ 6/12/24 VDC 

Overall Dimensions: 

See Figure 1

Operating Temperature Range: 

–40°F to +160°F

Maximum Service Pressure: 

EPS40-1, EPS40-2:  

300 PSI

 

EPS120-1, EPS120-2:   300 PSI

Adjustment Range: 

EPS40-1, EPS40-2:  

10-100 PSI

 

EPS120-1, EPS120-2:   10-200 PSI

Enclosure Rating: 

UL 4x — Indoor or Outdoor Use

 

NEMA 4 — Indoor or Outdoor Use

 IP54
Approximate Differential: 

EPS40-1, EPS40-2: 

3 PSI at 10 PSI

 

   

 

6 PSI at 100 PSI

 

EPS120-1, EPS120-2: 

3 PSI at 10 PSI

 

   

 

9 PSI at 200 PSI

WARNING

High voltage. Electrocution hazard. Do not handle live AC wiring or work on 
a device to which AC power is applied. Doing so may result in severe injury 
or death. When utilizing switches at voltages greater than 74 VDC 

 or 

49 VAC 

, means to provide all-pole disconnection must be incorporated in 

the field wiring, such as a circuit breaker.

3.   Wire the device in accordance with the National Electrical Code. Two 

7

/

8

 

diameter conduit connection holes have been provided in the mounting 
plate to accept standard 

1

2

 conduit fittings (one is removable knock-out 

type). If a NEMA 4/UL 4x (waterproof unit) is required, waterproof flex-
ible metallic conduit and appropriate conduit fittings must be used. Rec-
ommended connectors are Thomas and Betts PN 5332 (180° coupling), 
PN 5352 (90° coupling), and PN 5262 seal ring.

4.  Connect wiring to terminals (see Figure 4 and Table 1).
Adjustments to Factory Settings

FIGURE 1. PRESSURE SWITCH BASIC DIMENSIONS:

W0170-00

I56-0986-008R

APPENDIX B

Summary of Contents for STANDPIPE-PAC SSS-101




































































Reviews: