background image

Description

Wilkerson Manual Dryers are intended to remove water vapor from the 

compressed  air  system.  Atmospheric  dew  points  as  low  as  -100°F  (-

73°C) are achievable when operated within rated unit specifications.

General Safety Information

  • 

Release all air pressure from intended airline before installation.

  • Install unit in air line before opening desiccant container. After unit 

installation, add desiccant following steps in desiccant replacement 

instructions on page 2.

  • Always  make  sure  bowl,  bowl  guard,  and  clamp  ring  are  in  place 

and the clamp ring is securely locked before pressurization.

  • DO NOT exceed the pressure and temperature ratings as shown in 

the specifications.

  • Follow  all  local,  state  and 

federal  EPA,  OSHA,  and 

similar  codes  regarding 

disposal of old desiccant.

Installation

  1. 

Refer to WARNING

 

(on page 6).

  2.  Install as close as possible to the point where the air is being used.
  3.  Install unit with the airflow going in the direction of the arrow. For the 

X04, install with airflow entering at the bottom center port of the 4-way 

valve and exiting at the center port of the shuttle valve.

  4.  Install  unit  on  air  line  before  opening  desiccant  container.  After 

installation, add desiccant. Shake and tap bowl while filling to settle 

desiccant. Fill Model X25 and X03/X04 to 1/8" below inner shoulder 

of bowl. Fill Model X06 bowl to within 1/2" of top.

  5.  Replace bowl and bowl guard, or metal bowl, and clamp ring onto 

the  unit.  Be  sure  clamp  ring  is  securely  locked  in  place  before 

pressurizing unit.

  6. Most manual desiccant dryer users will achieve optimal results when 

installing the dryer as close to the equipment or process being protected 

as possible in the compressed air system. Most users, especially those 

with high quality air requirements, should protect their system and the 

manual dryer with one or more of the following types of components: 

Please see page 4 for exact model recommendations.
•   Liquid Separator:  

Should be used prior to the manual desiccant 

dryer in any system where large slugs of liquid water are anticipated. 

The manual desiccant dryer silica gel or mole sieve can be destroyed 

by large amounts of liquid moisture. Most systems which have an 

aftercooler  and  separator,  and/or  a  refrigerated  air  dryer,  will  not 

require a liquid separator. An alternative is to use a particulate filter/

separator, described below.

•   Particulate Filter/Separator:  

Should be used prior to the manual 

desiccant dryer in any system where significant amounts of dirt, 

pipe scale, etc, and/or liquid water, is present, in order to prevent 

clogging the manual dryer or harming the desiccant. A particulate 

filter/separator should be used prior to a coalescing filter to extend 

the life of the coalescing element.

Specifications

X06

X03 Plastic Bowl

X03 Metal Bowl

X04

X25 Metal Bowl

Maximum Pressure

150 psig (10.3 bar)

150 psig (10.3 bar)

150 psig (10.3 bar)

150 psig (10.3 bar)

150 psig (10.3 bar)

Maximum Temperature

125°F (52°C)

125°F (52°C)

150°F (66°C)

125°F (52°C)

150°F (66°C)

Atmospheric Dewpoint*

  000 Model:  Silica Gel

  U00 Model:  4A Molecular

   

Sieve

000 Model:

-45°F (-43°C)

U00 Model:

-100°F (-73°C)

000 Model:

-45°F (-43°C)

U00 Model:

-100°F (-73°C)

M00 Model:

-45°F (-43°C)

MU0 Model:

-100°F (-73°C)

000 Model:

-45°F (-43°C)

U00 Model:

-100°F (-73°C)

000 Model:

-45°F (-43°C)

U00 Model:

-100°F (-73°C)

Maximum Continuous Airflow*

5 scfm (2.3 dm

3

/s)

10 scfm (4,7 dm

3

/s)

10 scfm (4.7 dm

3

/s)

10 scfm (4.7 dm

3

/s)

25 scfm (11.8 dm

3

/s)

Total Airflow*

600 scf (283 dm

3

)

4400 scf (2076 dm

3

)

4400 scf (2076 dm

3

)

4400x2 scf (2076x2 dm

3

) 11,000 scf (5191 dm

3

)

Total Min. of Operation @ 

Max Continuous Airflow

120 min.

440 min.

440 min.

880 min.

440 min.

Unit Weight With Desiccant

1.13 lbs. (0.51 kg)

7.4 lbs. (3.4 kg)

6.8 lbs. (3.1 kg)

15.0 lbs. (6.8 kg)

11.2 lbs. (5.1 kg)

# of Desiccant Bags/Charge

1 Bag **

2 Bags ***

2 Bags***

4 Bags***

5 Bags***

Pipe Connections

1/4" NPT (BSPP)

1/4", 1/2" NPT (BSPP) 1/4", 1/2" NPT (BSPP)

1/4", 1/2" NPT (BSPP)

1/2" NPT (BSPP)

*With Dry Desiccant at 100 psig (7 bar) and 70°F (21°C)

** Each bag weighs .25 lbs. (.11kg)

*** Each bag weighs .88 lbs. (.40kg)

Installation & Service Instructions
83-050-000
Manual Desiccant Dryer Models 

X06, X03, X04, and X25 with 
Variations and Accessories
ISSUED:  April, 2013
Supersedes:  April, 2007

Doc. #83050000, EN #130200, Rev. 4

!

 

    WARNING

To avoid unpredictable system behavior that can cause personal injury 

and property damage:

•  Disconnect  electrical  supply  (when  necessary)  before  installation, 

servicing, or conversion.

•  Disconnect air supply and depressurize all air lines connected to this 

product before installation, servicing, or conversion.

•  Operate within the manufacturer’s specified pressure, temperature, 

and other conditions listed in these instructions.

•  Medium  must  be  moisture-free  if  ambient  temperature  is  below 

freezing.

•  Service according to procedures listed in these instructions.
•  Installation,  service,  and  conversion  of  these  products  must  be 

performed  by  knowledgeable  personnel  who  understand  how   

pneumatic products are to be applied.

•  After installation, servicing, or conversion, air and electrical supplies 

(when necessary) should be connected and the product tested for 

proper  function  and  leakage.  If  audible  leakage  is  present,  or  the 

product does not operate properly, do not put into use.

•  Warnings and specifications on the product should not be covered by 

paint, etc. If masking is not possible, contact your local representative 

for replacement labels.

Safety Guide

For more complete information on recommended application guidelines, see the 
Safety Guide section of Pneumatic Division catalogs or you can download the 

Pneumatic Division Safety Guide

 at: www.wilkersoncorp.com

Richland, MI 49083 

Tel: (269) 629-5000

Model X03

1

APPENDIX C

Summary of Contents for STANDPIPE-PAC SSS-101




































































Reviews: