background image

GENERAL AIR PRODUCTS, INC. 

For Assistance Please Call 1-800 345-8207 

Please keep these instructions for future reference. 

OILLESSINST  

REV 080906 

diameter to minimize pressure drop from the 
compressor to system.  Larger pipe size may be 
required by code and may be substituted with no 
adverse effects.  Smaller line size must not be used 
and will restrict the compressor flow, lowering 
capacity and causing the compressor/motor to work 
harder, which shortens compressor/motor life.  All 
piping connected to the compressor must  be fully 
supported and not transfer any loads to the 
compressor. 
If an AMD-1 is used, allow sufficient distance 
between the compressor and AMD-1 to ensure that the 
maximum temperature at the AMD-1 is 200

o

F or less.  

When an AMD is used with riser mounted units, a 
riser mounted tank kit (p/n OLR-TK) should be 
installed to prevent short cycling the compressor.

 

All oil-less compressors include a relief valve.  For 
riser mounted models, the relief valve is installed on 
the compressor outlet.  For tank mounted models, an 
ASME Code relief valve is mounted on the 
compressor’s tank.  This valve will open at a preset 
value above the pressure switch setting to prevent 
excess tank pressure in the event of switch failure. 

WARNING: 

Do not attempt to change the 

safety relief valve setting

A manual drain is provided on the bottom of each tank 
mounted compressor.  Moisture accumulated in the 
tank, must be drained weekly.  An automatic drain , 
P/N DVA -2T, is recommended in areas of high 
humidity. 
The compressor outlet piping should contain an 
accessible drain.  As a minimum a manual drain may 
be used, but an automatic drain is recommended to 
remove excess water. 

NOTE:

 

Accumulation of condensed water in a 

system causes corrosion of components and 
reduces system capacity. 

NOTICE:

 

Warranty is void if a separate check 

valve is not installed to prevent water back flow.

 

Wiring (reference “Wiring Instructions” 
drawings) 

WARNING 

Have a qualified electrician wire the compressor 
to ensure that the supply line has the same 
characteristics (voltage, frequency and phasing) 
as the motor. Wiring must comply with all local 
and national codes. 

 

CAUTION 

Inadequate wiring size can cause insufficient 
voltage at the compressor during start -up. 
Overheating and damage to the motor and 
controls may result  

The supply wire must be of adequate size and no other 
equipment should be connected to the same line.  The 
table below lists the recommended wire size for each 
model, based on a 100’ run.  Consult factory for 
longer runs. 

MINIMUM RECOMMENDED WIRE SIZE 

MODEL 

1 PHASE 

3 PHASE 

OL11016** 

12 

N/A 

OL21533** 

10 

N/A 

OL33550** 

12 

OL42575** 

12 

OL435V75** 

12 

OL525100** 

12 

OL610V100** 

12 

OL675150** 

12 

OL900V100** 

12 

OL900V150** 

12 

OL1200V200** 

10 

10 

The motors supplied are multiple voltage motors.  A 
label on the pressure switch cover indicates the voltage 
the motor is pre-wired for.  If the supply voltage, on 
site, is different from the voltage indicated on this 
label, change the internal motor voltage connections to 
match the supply voltage.  To change internal voltage 
connections, remove the cover plate located on the 
rear or side of the motor and reconnect the wire leads 
as shown on the motor’s wiring diagram.  
On all three phase and ½ Hp and ¾ Hp single phase 
models, an arrow on the motor indicates the direction 
of rotation of the compressor.  If the compressor 
rotates in the opposite direction, reverse the rotation of 
the motor.  On single phase units, reverse motor 
rotation by interchanging the red and black motor 
leads.  Interchanging any two incoming supply wires 
reverses rotation of three phase motors. 

NOTICE: 

Single-phase oil-less 

compressors can not be operated at 208V.  
Operating the compressor at 208V voids the

 

warranty.

 

NOTICE

Single-phase motors include 

internal thermal overload protection, which has 
an automatic reset device.

   

WARNING:

  Disconnect electrical power 

before servicing to disable reset devices.  
Thermal protection can automatically start the 
motor when the protector resets. 

On single phase models, the motor is pre-wired to the 
pressure switch provided, which controls starting (cut 

Summary of Contents for STANDPIPE-PAC SSS-101




































































Reviews: