4
COMPLIANCE STATEMENTS AND ACKNOWLEDGEMENTS
–
SECTIONS 60.533(B) AND 60.5475(B)
INSTRUCTIONS: PLEASE READ THE BELOW STATEMENTS AND AFFIRMATIONS AND ADDRESS ACCORDINGLY.
FOR EMISSIONS DATA SUMMARY TABLES SEE ATTACHMENTS
1.
Engineering Drawings Statement
Engineering drawings and specifications of components that may affect emissions (including specifications for each
component listed in paragraphs (k)(2), (3) and (4) of 60.533(b) and 60.5475(b). Manufacturers may use assembly or
design drawings that have been prepared for other purposes, but must designate on the drawings the dimensions of
each component listed in paragraph (k) of this section. Manufacturers must identify tolerances of components listed in
paragraph (k)(2) of 60.533(b) and 60.5475(b) that are different from those specified in that paragraph, and show that
such tolerances cannot reasonably be anticipated to cause wood heaters in the model line to exceed the applicable
emission limits. The drawings must identify how the emission-critical parts, such as air tubes and catalyst, can be
readily inspected and replaced.
2.
Firebox Statement Requirement
A statement whether the firebox or any firebox component (including the materials listed in paragraph (k)(3) of
60.533(b) and 60.5475(b) will be composed of material different from the material used for the firebox or firebox
component in the wood heater on which certification testing was performed, a description of any such differences and
demonstration that any such differences may not reasonably be anticipated to adversely affect emissions or efficiency.
3.
CBI
Clear identification of any claimed confidential business information (CBI). Submit such information under separate
cover to the EPA CBI Office; Attn: Residential Wood Heater Compliance Program Lead, 1200 Pennsylvania Ave., NW,
Room 7138, MS:2227A, Washington, DC 20460. Note that all emissions data, including all information
necessary to determine emission rates in the format of the standard, cannot be claimed as CBI.
4.
Valid Certification Statement
All documentation pertaining to a valid certification test, including the complete test report and, for all test runs: Raw
data sheets, laboratory technician notes, calculations and test results. Documentation must include the items specified
in the applicable test methods. Documentation must include discussion of each test run and its appropriateness and
validity, and must include detailed discussion of all anomalies, whether all burn rate categories were achieved, any data
not used in the calculations and, for any test runs not completed, the data collected during the test run and the
reason(s) that the test run was not completed and why. The burn rate for the low burn rate category must be no
greater than the rate that an operator can achieve in home use and no greater than is advertised by the manufacturer
or retailer. The test report must include a summary table that clearly presents the individual and overall emission rates,
efficiencies and heat outputs. Submit the test report and all associated required information, according to the
procedures for electronic reporting specified in § 60.537(f) and 60.5475(f).
5.
Warranties
A copy of the warranties for the model line, which must include a statement that the warranties are void if the unit is
used to burn
materials for which the unit is not certified by the EPA and void if not operated according to the owner’s
manual.
6.
Q/A Statement
A statement that the manufacturer will conduct a quality assurance program for the model line that satisfies the
requirements of paragraph (m) of this section.
7.
Laboratory Sealing of Unit
A statement describing how the tested unit was sealed by the laboratory after the completion of certification testing
and asserting that such unit will be stored by the manufacturer in the sealed state until 5 years after the certification
test.
8.
Statements that the wood heaters manufactured under this certificate will be
—
(i)
Similar in all material respects that would affect emissions as defined in § 60.531 to the wood heater
submitted for certification testing, and labeled as prescribed in § 60.536 and 60.5478.
(ii)
Accompanied by an owner’s manual that meets the requirements in §
60.536 and 60.5478. In addition,
a copy of the owner’s manual must be submitted to the Administrator and be available to the public on
the manufacturer’s web site.
9.
Third Party Certification Statement
A statement that the manufacturer has entered into contracts with an approved laboratory and an approved third-party
certifier that satisfy the requirements of paragraph (f) of this section.
Summary of Contents for KP5522
