background image

USSC

1

851621B

CORN & PELLET MULTIFUEL STOVE

6039, 6039T

OWNER’S MANUAL

Installation - Operation - Maintenance Instructions - Repair Parts

READ THIS ENTIRE MANUAL, THOROUGHLY, BEFORE ATTEMPTING TO INSTALL AND/OR

BURN YOUR NEW AMERICAN HARVEST CORN AND PELLET MULTI-FUEL STOVE. FAILURE TO

FOLLOW THESE INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURIES

OR EVEN DEATH.

SAVE THESE INSTRUCTIONS

UNITED STATES STOVE COMPANY GRANTS NO WARRANTY, IMPLIED OR STATED,

FOR THE INSTALLATION OR MAINTENANCE OF THE STOVE AND ASSUMES NO

RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

UNITED STATES STOVE COMPANY - 227 INDUSTRIAL PARK ROAD-SOUTH PITTSBURG, TN. 37380

TECHNICAL ASSISTANCE (423) 837-2100 - (423) 837-2109 FAX

Safety Notice:  If this stove is not properly installed, a house fire may result.

For your safety, follow the installation directions. Contact local building or fire officials

about restrictions and installation requirements peculiar to your area.  Do Not Plug

this appliance into an electrical outlet before reading and understanding all operations

and always unplug the unit before attempting any work or maintenance.  Do not

connect this stove to any chimney flue already serving another appliance.  Carefully

observe and maintain all clearances to combustibles.

A note about fuel:  Use only dried shelled corn with a moisture content of 14%

or less (11 to 12% provides the best results); any pellet fuel used should have

an ash content of 1% or less.  If not, efficiency will suffer, and your warranty may be

voided.

Your American Harvest Corn/Pellet Stove operates on a negative pressure.  Therefore,

all venting connections (elbows, T-pipe) must be sealed and airtight.

Use Hi-Temp silicone at each joint or connection.

K e e p i n g

K e e p i n g

K e e p i n g

K e e p i n g

K e e p i n g

North 

North 

North 

North 

North  America W

America W

America W

America W

America Warm

arm

arm

arm

arm

Since 1869

Since 1869

Since 1869

Since 1869

Since 1869

Summary of Contents for American Harvest 6039

























Reviews: