background image

Whenever a high amount of smoke is noticed in the room, you must: 
 
1.  Open doors and windows. 
 
2.  Make sure the furnace door is closed as well as the damper (if necessary, lower the thermostat starting point or 

undo the chain of the damper and close the barometric draft control manually). 

 
3. When the furnace has cooled down, inspect the chimney to detect obstructions and consult a specialist to 

determine the cause of the smoke spillage. 

 
 
 

CARBON MONOXYDE IS A LETHAL GAS (ODOURLESS AND COLOURLESS), WHICH YOU MUST 
BEWARE OF. 
 
 
 

4.3.3 CHIMNEY FIRES 

 
    They might occur when the fire gets extremely hot; burning paper, cardboard, branches or small pieces of wood 
can ignite the creosote residues accumulated in the evacuation flue system.  The usual signs are: 
 
1. Rumbling 
 
2.  The flue gets extremely hot 
 
3.  Sparks are coming out of the chimney 
 
 
  

 

 In case of a chimney fire, call your local fire department immediately and sprinkle the 

roof around the chimney with water. 

 

    Make sure that the furnace door is closed as well as the damper (if necessary, lower the thermostat starting point 
or release the chain from the damper and CLOSE the barometric draft control manually). 
 
 
 
    If the fire gets uncontrollable due to  improper use or because the draft is too strong, follow the same procedure 
as in a chimney fire except that you will have to OPEN the barometric draft control  manually. 
 
 
 
 

 

 
 

LOCAL FIRE DEPARTMENT.

 

 
 
Phone number: ___________________________________ 

 

11

Summary of Contents for HOTBLAST 1950





















Reviews: