background image

LOCATING THE HEATER

AS A LOCATION IS SELECTED,
KEEP THE FOLLOWING IN MIND:

1.  The chimney connection should be as short
as possible. The heater must have its own
chimney flue. Do not connect this unit to a
chimney flue serving another appliance. If there
is no chimney near where you wish to place the
heater, you can use a UL 103HT Residential
Type and Building Heating Appliance Chimney
(Fig. 5,6,6A,&6B).

2.  Place the heater on solid masonry or solid
concrete. When the heater is used on a com-
bustible floor protector of one layer of 3/8"
millboard having a thermal conductivity of
K=0.84 BTU in./ft. 2 hr. Deg. F with 28-gauge
sheet metal or a UL Listed floor protector. Have
the floor protector extend 16" beyond the door
side of the heater and under the connector pipe
in the back.

3.  Check Figures 2, 3, and 4. Be sure you have
the clearances shown from the heater and the
connector pipe to combustible surfaces. If you
have a SOLID brick or stone wall behind your
heater, you can place the heater as close as
you wish to the wall. If the wall is only faced with
brick or stone, treat it as a combustible wall.

4

21

Fig. 2

Fig. 4

17"

27"

16"

20"

54"

19 1/4"

36"

4 3/4"

NOTE: DASHED LINES SHOW
STRAIGHT UP AND THROUGH
THE WALL INSTALLATION

10"

32 1/4"

16"

FLOOR PROTECTOR
(TOP VIEW)

SIDEWALL

NON-COMBUSTIBLE
CONSTRUCTION IN
ACCORDANCE WITH
NFPA 211

12"

12"

Fig. 3

NOTE: BEFORE FIRING

HEATER

1. Remove plastic knob from

inside of cabinet door and

install on outside of door.

(See Page 15)

2.Slide firebricks toward the

rear so no gaps remain

between them.

CAUTION:

Keep furnishings and other

combustible materials away

from the heater.

STOP:  Before connecting

the flue pipe, check the
"SOLID FLUE DAMPER

INSTALLATION".

 (page 6)

F36 BLOWER KIT

An Optional Blower kit is available for the 2931 Wonderwood
automatic wood burning circulator heater.  If this kit is not available
where you have purchased this Wonderwood heater, you can
purchase the F36 Blower Kit directly from the factory.  To order
contact the United States Stove Company at the address and
telephone number given on the back page.

Summary of Contents for WONDERWOOD 2931













Reviews: