background image

GO1 User Manual

 

Copyright © 2021 Unitree Robotics. All Rights Reserved

 

11

 

 
 
 
 

 

 

 

 

 

 

 
 

Startup and Shutdown                                                                                                     

Startup 

After placing the robot according to the requirements in the “Preparing Before 

starting up

” section, start 

the following steps: short press the power switch once, then press and hold the power switch for more 
than 2 seconds to turn on the battery (when the battery is turned on, the indicator light is the green light 
is always on and the indicator shows the current battery level). Then the robot will perform the power-
on self-test. If the self-test is successful, the robot will stand up to the initial height of the body, and the 
boot is successful. If the robot is not stand up during the above process, the robot fails the self-test. If 
the boot fails, the robot can't stand up. At this time, you need to re-start the body according to the two 

steps of “body placement”    in the “Preparing 

Before Starting Up

” section

Shutdown 

Before shutting down, please make sure that the robot stands on the level of the ground, make sure that 
the robot is in Static Standing State (the height of the robot body is at the initial height after starting up, 
the body level, the joystick has no operation, the state when standing statically).  Press and hold the 
handle L2 button, then click the A button three times, the robot will then complete the squat, stand up, 
and lie down; then hold down the handle L2 button, and then click the B button twice, the robot then 
completes prone (Damping), prone (undamped) action; after the robot enters the prone (undamped) 
state, press the power switch once, then press the power switch for more than 2 seconds to turn off 
battery. When the battery is turned off, the indicators are off. After shutting down, please adjust the size 
of the robot's size legs and hips according to the requirements in the "Preparation before starting" section, 
and prepare for the next boot. 

 

Since the actual control personnel have different levels of control proficiency, in order to be 
reliable and stable, please use it in an open and flat environment. When operating the robot, 
be careful to avoid steps above 5cm, slopes greater than 25

°, and obstacles that may cause 

the robot to fall. When the robot is walking on a terrain with a certain undulation or slope, the 
controller should reduce the walking speed of the robot. 

 

The robot have certain requirements for the ground to walk. Do not use robot on the ground 
with very low friction, such as ice. Do not use robot on soft ground, such as thicker sponge 
floors. For use on smoother floors, such as glass, tiles, etc., carefully and compliantly control 
the robot to exercise, avoid strenuous exercise, and reduce the walking speed of the robot to 
prevent the robot's foot from slipping and falling. 

Summary of Contents for Go I














































Reviews: