background image

GO1 User Manual

 

Copyright © 2021 Unitree Robotics. All Rights Reserved

 

12

 

After shutting down, please adjust the size of the robot's size legs and hips according to the requirements 
in the "Preparation before starting" section, and prepare for the next boot. 
 
 

 
 
 
 
 

Battery Pack                                                                                                                       

Introduction 

The battery pack is designed for the GO1 with a capacity of 6300 mAh and a voltage of 21.6 V with 
charge and discharge management. The battery pack features a high-performance battery and uses the 
advanced battery management system developed by Unitree to provide sufficient power for the GO1. 

The battery pack must be recharged using a dedicated charger from Unitree. 

Technical specifications 

parameter 

Specification 

Remark 

Rated voltage (power supply) 

22.2V 

 

Rated current (power supply) 

 

Current jump 

Rated voltage (charging)   

25.2V 

 

Rated current (charging) 

6A 

 

Rated Capacity 

6000mAh,133.2Wh 

 

operation hours 

1h 

 

frequency 

4492.8MHz 

 

 

 

The step of shut down will be described in the "Joystick Operation" section.

 

 

Please pay attention to Unitree's official website - service and support - technical support - 
firmware update or contact Unitree staff. We will develop a one-button shutdown function as 
soon as possible, and upload the firmware. At that time, the customer can update the firmware 
to make the robot have a one-button shutdown function.

 

 

Be sure to fully charge the battery before using it for the first time.

 

Summary of Contents for Go I














































Reviews: