Unitron Gemscope 3075-GS Manual Download | Manualshive

Page: 6 / 15

background image

GEMSCOPE

UNITRON

®

73 Mall Drive, Commack, NY 11725 • 631-543-2000 • www.unitronusa.com

6

ASSEMBLY DIAGRAM

The diagram below shows how to assemble the various components. The numbers indicate the order of
assembly.

When assembling the Gemscope, make sure that all parts are free of dust and dirt, and avoid scratching
any parts or touching glass surfaces.

Stereo Head

Lock Screw

Power Cord

Eyepieces

Fluorescent

Illuminator

Gem Clamp

«
...
4
5
6
7
8
...
»

Summary of Contents for Gemscope 3075-GS
















Reviews:

No comments

Related manuals for Gemscope 3075-GS

DUO SCOPE MFL-06

Brand: My First Lab Pages: 16

Brand: Cosmos Pages: 40

Brand: THORLABS Pages: 13

Brand: Olimpus Pages: 470

Brand: Bresser Pages: 20

Brand: Accu-Scope Pages: 23

Brand: Zeiss Pages: 94

Brand: Sharper Image Pages: 58

Brand: Accu-Scope Pages: 24

Brand: Zeiss Pages: 38

Brand: Westfalia Pages: 9

Brand: Learning Resources Pages: 19

Research Scope T-29031

Brand: Ken A Vision Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands