background image

 

Z850 STEREO MICROSCOPE 

 

 

 

 
 

UNITRON

®     

                          

73 Mall Drive, Commack, NY  11725  •  631-543-2000  •  www.unitronusa.com 

4

 

INTRODUCTION 

Congratulations on the purchase of your new UNITRON

®

 microscope. UNITRON

®

 microscopes are 

engineered and manufactured to the highest quality standards. Your microscope will last a lifetime if 
used and maintained properly. UNITRON

®

 microscopes are carefully assembled, inspected and tested 

by our staff of trained technicians in our New York facility. Careful quality control procedures ensure each 
microscope is of the highest quality prior to shipment.  
 
 

 

UNPACKING AND COMPONENTS 

Your microscope arrived packed in a molded shipping carton. 

Do not discard the carton

:  

the shipping 

carton should be retained for reshipment of your microscope if needed. Avoid placing the microscope in 
dusty surroundings or in high temperature or humid areas as mold and mildew can form. Carefully 
remove the microscope from the shipping carton and place the microscope on a flat, vibration-free 
surface. 

 

 
COMPONENTS DIAGRAM

 

 

NOTE:

  Stand ordered may not be as pictured above. 

 

 

Binocular Head 

Stand 

Focusing Knob 

Power Cord 

Shift Knob 

Switch 

Base 

Eyepieces 

Lock-screw 

Stage Plate 

Summary of Contents for Z850 Series













Reviews: