background image

Unitronics

1

EX-RC1

 

Remote I/O Adapter

The EX-RC1 interfaces between Unitronics Vision OPLCs and remote I/O Expansion Modules distributed 
throughout your system. 
The adapter is connected to a PLC via CANbus. Each adapter may be connected to up to 8 I/O Expansion 
Modules. The network may comprise up to 60 nodes, including both PLCs and adapters; note that the PLC 
must comprise a CANbus port. Communication is via UniCAN, Unitronics’ proprietary CANbus protocol.  
The EX-RC1 is run by a factory-installed application. For more information refer to the Remote I/O topics in 
the VisiLogic Help system. 

The EX-RC1 may either be snap-mounted 
on a DIN rail, or screw-mounted onto a 
mounting plate.

 

POWER

EX-RC1

0V

V

Remote I/O Adapter

PRG

Network ID

CANbus

PWR

I/O COMM.

Bus COMM.

Component identification 

1

Status indicators 

2

PC to EX-RC1 connection port 

3

Power supply connection points 

4

EX-RC1 to expansion module  
connection port 

5

CANbus port 

6

DIP Switches 

Before using this product, it is the responsibility of the user to read and understand this document and
any accompanying documentation.
All examples and diagrams shown herein are intended to aid understanding, and do not guarantee
operation.  Unitronics accepts no responsibility for actual use of this product based on these examples.
Please dispose of this product in accordance with local and national standards and regulations.
Only qualified service personnel should open this device or carry out repairs.

User safety and equipment protection guidelines 

This document is intended to aid trained and competent personnel in the installation of this equipment as 
defined by the European directives for machinery, low voltage, and EMC.  Only a technician or engineer trained 
in the local and national electrical standards should perform tasks associated with the device’s electrical wiring. 

Symbols are used to highlight 
information relating to the user’s 
personal safety and equipment 
protection throughout this document.  
When these symbols appear, the 
associated information must be read 
carefully and understood fully. 

Symbol Meaning 

Description 

Danger 

The identified danger causes physical 
and property damage. 

Warning 

The identified danger can cause 
physical and property damage. 

Caution

 

Caution Use 

caution. 

Summary of Contents for EX-RC1









Reviews: