background image

Vision™ OPLC™ V570-57-T20B, V570-57-T40B 

Installation Guide

 

 Unitronics 

 

 

CANbus 

These controllers comprise a CANbus port. Use 
this to create a decentralized control network using 
one of the following CAN protocols: 

ƒ

  CANopen: 127 controllers or external 

devices 

ƒ

 Unitronics’ 

proprietary 

UniCAN: 

60 

controllers, (512 data bytes per scan) 

The CANbus port is galvanically isolated. 

CANbus Wiring 

Use twisted-pair cable. DeviceNet® thick shielded 
twisted pair cable is recommended. 

Network terminators: These are supplied with the 
controller. Place terminators at each end of the 
CANbus network.  

Resistance must be set to 1%, 121

, 1/4W. 

Connect ground signal to the earth at only one 
point, near the power supply. 

The network power supply need not be at the end 
of the network 

CANbus Connector 

 

24V Power Supply

+

+V

L

PE

H

+V

Circuit

protection

device

121 

terminating

resistor

121 

terminating

resistor

+V

L

PE

H

+V

+V

L

PE

H

+V

 

 

 
 

 
 
 

 

 
 
 

 

 
 
 

 

 

The information in this document reflects products at the date of printing. Unitronics reserves the right, subject to all applicable laws, at any time, at its sole 

discretion, and without notice, to discontinue or change the features, designs, materials and other specifications of its products, and to either permanently or 

temporarily withdraw any of the forgoing from the market. 
All information in this document is provided "as is" without warranty of any kind, either expressed or implied, including but not limited to any implied warranties of 

merchantability, fitness for a particular purpose, or non-infringement. Unitronics assumes no responsibility for errors or omissions in the information presented in 

this document. In no event shall Unitronics be liable for any special, incidental, indirect or consequential damages of any kind, or any damages whatsoever arising 

out of or in connection with the use or performance of this information. 
The tradenames, trademarks, logos and service marks presented in this document, including their design, are the property of Unitronics (1989) (R"G) Ltd. or other 

third parties and you are not permitted to use them without the prior written consent of Unitronics or such third party as may own them.

 

DIG-V570-TX0B 08/08

 

 

Summary of Contents for V570-57-T20B









Reviews: