background image

24

FCC NOTICE

This equipment has been tested and found to comply 
with the limits for a class B digital device, pursuant to 
part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful 
interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy 
and if not installed and used in accordance with the 
instructions, may cause harmful interference to radio 
communications. 
However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does 
cause harmful interference to radio or television 
reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following 
measures: 

Reorient or relocate the receiving antenna. 

Increase the separation between the equipment and 
receiver. 

Connect the equipment into an outlet on a circuit 
different from that to which the receiver is 
connected. 

Consult the dealer or an experienced radio/TV 
technician for help. 

It is strongly recommended that the TV be plugged 
into a separate wall outlet.

This equipment has been verified to comply with the 
limits for a class B computing device, pursuant to FCC 
Rules. In order to maintain compliance with FCC 
regulations, shielded cables must be used with this 
equipment. Operation with non-approved equipment or 
unshielded cables is likely to result in interference to 
radio and TV reception. The user is cautioned that 
changes and modifications made to the equipment 
without the approval of manufacturer could void the 
user’s authority to operate this equipment. 
FCC ID: MG32150 

Summary of Contents for MTS 2150


























Reviews: