background image

MRF-260i B

ASE

S

TATION

Page 11

Limited Warranty Statement

1. LIMITED WARRANTY AND DISCLAIMERS

Universal Remote Control, Inc. (“URC”) warrants that URC

equipment purchased directly from URC or from an authorized

URC dealer or distributor shall be free from defects in material and

workmanship under normal usage for a period of one (1) year from

the date of purchase of the product by the end-user, but no longer

than thirty-six (36) months from the date of shipment of the URC

equipment by URC to an authorized URC dealer or distributor,

except that with respect to Total Control® whole-house products,

the warranty extends for two (2) years from the date of purchase by

the end-user, but no longer than forty-eight (48) months from the

date of shipment of the URC equipment by URC to an authorized

URC dealer or distributor. 

This limited warranty is valid only in the United States of America. 

URC equipment purchased from other than an authorized URC

dealer or distributor is without warranty.

URC warrants that the software will substantially conform in any

material respect to its functional specifications at the time of

delivery. URC SHALL NOT BE LIABLE FOR OPERATIONAL,

TECHNICAL OR EDITORIAL ERRORS AND/OR OMISSIONS

MADE IN THE URC DOCUMENTATION. URC DOES NOT

WARRANT THAT THE URC SOFTWARE IS BUG-FREE OR ERROR

FREE OR THAT THERE ARE NO ERRORS/BUGS IN THE URC

SOFTWARE.

URC warrants that at the time of purchase the URC equipment and

the URC software complied with all applicable regulations and

policies of the Federal Communications Commission ("FCC")

regarding electromagnetic interference caused by

electronic/computing devices and to the extent that the URC

equipment and/or the URC software fails to so comply, URC shall,

at its own expense, take all reasonable measures to promptly cause

such to comply.

THIS LIMITED WARRANTY DOES NOT COVER TECHNICAL

ASSISTANCE FOR HARDWARE OR SOFTWARE USAGE EXCEPT

AS EXPRESSLY PROVIDED FOR HEREIN. 

CERTAIN IMPLIED WARRANTIES, INCLUDING AN IMPLIED

WARRANTY OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, MAY BE AVAILABLE WITH RESPECT TO

URC EQUIPMENT.  IMPLIED WARRANTIES VARY FROM STATE

TO STATE.  URC EXPRESSLY LIMITS THESE IMPLIED

WARRANTIES, TO THE EXTENT ALLOWABLE BY LAW, TO THE

TIME PERIODS COVERED BY THE EXPRESS WRITTEN

WARRANTIES PROVIDED HEREIN.  OTHERWISE AND EXCEPT AS

PROVIDED FOR HEREIN, URC EXPRESSLY DISCLAIMS ALL

WARRANTIES, EXPRESS, STATUTORY OR IMPLIED, AND MAKES

NO REPRESENTATIONS REGARDING THE USE OF, OR THE

RESULTS OF THE USE OF, THE EQUIPMENT, SOFTWARE OR

DOCUMENTATION IN TERMS OF CORRECTNESS, ACCURACY,

RELIABILITY OR OTHERWISE.

Summary of Contents for MRF-260i



















Reviews: