UPG FC9T-DH User Manual Download

Page: 12 / 16

272360-UUM-A-0407

Unitary Products Group

TABLE 2:

Field Installed Accessories - Non Electrical

MODEL NO.

DESCRIPTION

USED WITH

1NP0347

PROPANE (LP) CONVERSION KIT

ALL MODELS

1CT0302

CONCENTRIC INTAKE/VENT 2”

60, 80, 100 INPUT MBH

1CT0303

CONCENTRIC INTAKE/VENT 3”

100, 120 MBH

1PS0507

HIGH ALTITUDE PRESSURE SWITCH KIT

(Does Not Include Orifices)

60/1200

1PS0508

80/1200

1PS0509

80/1600

1PS0510

100/2000

1PS0511

120/2000

1NK0301

CONDENSATE NEUTRALIZER KIT

ALL MODELS

1HT0901

SIDEWALL VENT TERMINATION KIT 3”

ALL MODELS

1HT0902

SIDEWALL VENT TERMINATION KIT 2”

ALL MODELS

1CB0317

COMBUSTIBLE FLOOR BASE

17-1/2” CABINET

1CB0321

21” CABINET

1CB0324

24-1/2” CABINET

1TK0917

COIL TRANSITION KIT

17-1/2” CABINET

1TK0921

21” CABINET

1TK0924

24-1/2” CABINET

REPLACEMENT PART CONTACT INFORMATION

This is a generic parts list. To request a complete parts list, refer to the contact information below:

• Visit our website at www.source1parts.com for the following information:

1. Search for a part or browse the catalog.

2. Find a dealer or distributor.

3. Customer Service contact information.

a. Click on the “Brand Links” button

b. Click on the “Customer Service” button

• You can contact us by mail. Just send a written request to:

York International

Consumer Relations

5005 York Drive

Norman, OK 73069

Summary of Contents for FC9T-DH

















Search results

Summary of Contents for FC9T-DH

Reviews:

Related manuals for FC9T-DH

Brands by name

Popular brands

UPG FC9T-DH, User Manual

Search results

Summary of Contents for FC9T-DH

Reviews:

Related manuals for FC9T-DH

Brands by name

Popular brands