background image

1 Copyright and disclaimer

Uponor has prepared this installation and operation manual and all
the content included solely for information purposes. The contents of
the manual (including graphics, logos, icons, text, and images) are
copyrighted and protected by worldwide copyright laws and treaty
provisions. You agree to comply with all copyright laws worldwide in
your use of the manual. Modification or use of any of the contents of
the manual for any other purpose is a violation of Uponor’s copyright,
trademark and other proprietary rights.

The presumption for the manual is that the safety measures have
been fully complied with and that the Port system as covered by the
manual (including any components ):

is selected, planned and installed and put into operation by a
licensed and competent planner and installer in compliance with
current (at the time of installation) installation instructions
provided by Uponor as well as in compliance with all applicable
building and plumbing codes and other requirements and
guidelines;

has not been (temporarily or continuously) exposed to
temperatures, pressure and/or voltages that exceed the limits
printed on the products or stated in any instructions supplied by
Uponor;

remain in its originally installed location and is not repaired,
replaced or interfered with, without prior written consent of
Uponor;

is connected to potable water supplies or compatible plumbing,
heating and/or cooling products approved or specified by
Uponor;

is not connected to or used with non-Uponor products, parts or
components except for those approved or specified by Uponor;
and

does not show evidence of tampering, mishandling, insufficient
maintenance, improper storage, neglect or accidental damage
before installation and being put into operation.

While Uponor has made efforts to ensure that the manual is accurate,
Uponor does not guarantee or warrant the accuracy of the
information contained herein. Uponor reserves the right to modify the
specifications and features described herein, or discontinue
manufacture of the Uponor products described at any time without
prior notice or obligation. The manual is provided “as is” without
warranties of any kind, either expressed or implied. The information
should be independently verified before using it in any manner.

To the fullest extent permissible, Uponor disclaims all
warranties, expressed or implied, including, but not limited to,
the implied warranties of merchantability, fitness for particular
purpose and non-infringement.

This disclaimer applies to, but is not limited to, the accuracy, reliability
or correctness of the manual.

Under no circumstances shall Uponor be liable for any indirect,
special, incidental or consequential damages or loss that result
from the use of or the inability to use the materials or
information in the manual, or any claim attributable to errors,
omission or other inaccuracies in the manual, even if Uponor
has been advised of the possibility of such damages.

This disclaimer and any provisions in the manual do not limit
any statutory rights of consumers.

Combi Port XS

  |  

Installation and operation manual

  | 

3

Summary of Contents for Combi Port XS






























Reviews: