background image

This manual applies to models WehoPuts 5 and 10 (soft ware version 5.X) 

1. WehoPuts miniature wastewater 

treatment plant – general

1.1 General 

The WehoPuts miniature wastewa-
ter treatment plant is a bio-chemical 
domestic wastewater treatment 
system intended for year-round use. 
All wastewater is directed into the 
treatment plant without separate 
pre-treatment. Treated water then 
fl ows or is pumped to the discharge 
point.

Further information on the point 
and manner of discharge must be 
received from the local environmen-
tal authorities before installation.

The WehoPuts treatment plant 
has been designed to suit a certain 
number of persons and quantity of 
wastewater (calculated based on 
150l/person/day).

If household water is taken from a 
private well, its quality must meet 
the general recommendations to 
secure good operation of the treat-
ment plant.

Information on the function of the 
WehoPuts treatment plant is avail-
able from the display in the plant 
control unit and the signal lamp on 
the machine room ventilation pipe.

NOTE! The signal lamp must be 
monitored carefully. When the signal 
lamp is on, the treatment plant is 
functioning normally. When the 
light is fl ashing or has gone out, the 
treatment plant has a malfunction 
and the message on the control unit 
display must be checked immedi-
ately! 

To simplify plant operation 
monitoring, the WehoPuts 5 and 10 
treatment units off er an optional 
GSM modem allowing for treatment 
plant remote monitoring using GSM 
phones. The GSM modem must be 
specifi ed when ordering the treat-
ment plant, as well as the need to 
use more than one GSM phone.

The WehoPuts treatment plants 
have a 2-year warranty starting 
from the purchase date. The war-
ranty covers structural, manufactur-
ing and material errors reported to 
and verifi ed by the manufacturer. 
Detailed warranty conditions can 
be found in the warranty certifi cate 
supplied with the treatment plant.

MODEL

 

MAXIMUM LOAD

m

3

/day

MAXIMUM AMOUNT 

OF PERSONS

WehoPuts 5

0.75

5

WehoPuts 10

1.5

10

Table 1. WehoPuts treatment plant cleaning 
capacity 

1.2 Operational safety

The tank lid must always be care-
fully locked. 

Only the electrical con-
nections and cleaning 
process control proce-

dures specifi ed in the installation 
and operation manual may be 
performed during maintenance.

When fi lling the chemical container 
and handling the chemical pump, 
the corrosiveness of the chemicals 
used (pH 2) must always be taken 
into account. Therefore, special 
protective equipment such as rub-
ber gloves and protective glasses 
must be worn. The safety data 
sheet must be studied in advance. 
The treatment plant is equipped 
with device-specifi c automatic 
fuses and ground fault switches. 
Treatment plant grounding is done 

through the building’s main distri-
bution board.

NOTE! The control box casing may 
only be opened by a professional 
electrician.

1.3 Foreign material and debris 
in wastewater

Normal household wastewater, 
such as domestic water and toilette 
fl ushing water, is directed into the 
treatment plant.

Debris washed down with waste-
water may clog or damage the 
treatment plant pumps and stop 
the entire treatment process. To 
ensure the disturbance-free op-
eration of the plant, the following 
materials and items must not be 
fl ushed down with wastewater: 

• 

bottle caps and other small
metal items 

• cigarette 

butts 

• condoms 

• cotton 

buds 

• cotton 

wads 

• hand 

tissues 

• left over food 
• matches 
• medicine 
• nappies
• oil
• plastics
• petrol
• rubber
• sanitary 

towels

• sand
• snuff 
• soil
• solvents
• tampons
• waste
• 

other material that may clog 
pipes, pumps or the treatment 
plant

NOTE! To prevent the pumps from 
clogging, we recommend fl oor drain 
fi lters.

3

Summary of Contents for WehoPuts 10

































Reviews: