background image

10 

©

 All rights reserved. All trademarks are property of their respective owners.

 

APP-B Technical Specifications 

Model 

425A/AP 

525A/AP 

625A/AP 

825A/AP 

1000A/AP 

Configuration 

Capacity (VA) 

425 VA 

525 VA 

625 VA 

825 VA 

1000 VA 

Capacity (Watts) 

255 W 

315 W 

375 W 

495 W 

550 W 

Form 

Tower Type 

Input 

Voltage 

100 / 110 / 120 VAC or 220 / 230 / 240 VAC 

Input Voltage Range 

75 - 150 or 165 - 300 VAC 

Input Frequency Range 

50 Hz / 60 Hz (Auto Sensing) 

Output 

Waveform

(Battery-Mode)

 

Simulated Sine Wave 

Voltage 

100 / 110 / 120 VAC or 220 / 230/ 240 VAC 

Frequency

(Battery-Mode)

 

50 Hz / 60 Hz ± 0.5 Hz   

Transfer Time 

2 - 4 ms (Typical) 

Protection 

Full Protection 

Overload, Surge, Short Circuit 

Tele Communication 

RJ11 / RJ45 : AP model 

Battery 

Type 

12V 7.2Ah 

12V 9 Ah 

Quantity 

Typical Recharge Time 

6-8 hr to 90% 

Management & Communication 

Indicator 

LED Control Panel : IMP model 

Digital Control Panel : IMD model 

Communication Port 

USB B type : AP model 

Physical 

Dimensions (WxDxH) (mm) 

105 x 334 x 168 

Weight (kgs) 

6.1 

6.1 

6.3 

6.8 

6.8 

Shipping Dimensions (mm) 

196 x 410 x 263 

Shipping Weight (kgs) 

7.4 

7.4 

7.6 

8.1 

8.1 

Alarm 

Overload / Fault 

Continuous Beeping 

Battery Mode 

Beep every 2 seconds 

Low Battery 

Beep every 0.5 second 

Environment 

Operating Humidity 

  0-90 % RH at 0-40°C (Non-condensing) 

Audible Noise 

Less than 40 dB 

 

* Specifications are subject to change without further notice. 

* Specifications are for reference; actual information should be based on the real product.

 

Summary of Contents for 1000A/AP












Reviews: