background image

©

 All rights reserved. All trademarks are property of their respective owners.

 

EMC Statement 

These  products  are  tested  and  thereby  comply  with  the  conditions  of  CE 

regulation,  which  established  to  offer  sufficient  protection  against  dangerous 
interference for installation. Installation and use of the equipment should comply with 

the  instructions  provided  to  avoid  such  interference  due  to  the  amount  of 
radiofrequency energy that generates by the equipment; Despite this, we cannot assure 
that a certain amount of interference may not occur in some installations. 

If by turning on and off, you conclude that the equipment’s harmful interference 

influences  your  radio  or  television  reception,  use  one  of  the  following  preventive 
measures: 
 

 

Place the receiving antenna in a separate location or orientation 

 

Ensure a greater distance between the receiver and the equipment 

 

Ensure that your Equipment connects to an outlet on a separate circuit 

 

Contact  a  technician  experienced  with  radio  and  TV  or  the  dealer  for  technical 
assistance 

 

Declaration of Conformity Request 

Units labelled with a CE mark comply with the following stander and directives: 

 

EMC Directive 2014/30/EU 

 

LVD Directive 2014/35/EU 

 

Safety: EN 62040 - 1 

 

EMC: EN 62040 - 2 

The  EC  Declaration  of  Conformity  is  available  upon  request  for  production  with  a  CE 
mark. 

 

 
 

 

Summary of Contents for 1000A/AP












Reviews: