background image

Installation and use manual  models  FAST 02 e FAST 03           rev  1.0.0  October 2013         Page 14 di 19  

14

  MAINTENANCE 

UR  Fog  generators  not  require  special  care,  however,  it  is  recommended  the  support  of  qualified  and  authorized 
personnel for periodic annual monitoring, taking into account the following: 
 
- The charged cylinders have a limit of predetermined duration of 3 years. 
- The deadline is printed at the top of the cylinder. 
- Verify annually the functioning of the cylinder plates. 
- Check the air tightness of the circuit and the operation of the switch. 
- The efficiency of the batteries is crucial to guarantee the operation 
- It is recommended to return to your dealer the deadline cylinders but not ended even if not empty 
- An empty cylinder, being aluminum / steel can be recycled as the common cans 
- It is recommended to change the 6AA internal batteries once every 12 month 
 

UP / DOWN CYLINDER PLATES – SCROLLING TEST 

If you want only lower a cylinder plate after an activation without the cylinder, use the following instructions, from 
step 6: 
 
The scrolling check of the cylinder plates, is performed by activating the motors without cylinders with the following 
sequence: 

 

 
1)

 

Close the jumper 

W3

 putting the card in “service mode” 

2)

 

Close the jumper P3 in the RESET position  

3)

 

Hold down the button 

S1

 the buzzer beeps and then: 
-      Motor 1 down 

-

 

Motor 2 down 

-

 

Motor 1 up 

  

-

 

Motor 2 up 

4)

 

Release the button S1 (in this situation you can hear the noise of the 
Nozzle tamper pump and a slight smoke can exit from the nozzle) 

5)

 

Remove the jumper 

W3

 

 

6)

 

With a slight finger pressure on the cylinder plate of the first motor, 
push again the button S1 

7)

 

Replaced the cylinder plate of the first motor, without leaving S1,  
move the finger from the first cylinder plate to the second one.  

 
 
 
 
 
 
 

If there were no problems, the scrolling test is ended, otherwise contact the service center. 

 

 
 

If  the  plates  are  completely  escaped  you  will  need  two  down  cycles  for  repositioning. 
The motors of the cylinder plates are ALWAYS powered from the batteries, so that any action reduce 
the autonomy of them. 

 
 
 
 
 

Summary of Contents for FAST 02




















Reviews: