background image

15

E N G L I S H •

User’s manual

• Never pick up or carry a machine while the 
engine is running.
• Never start the machine if ice has formed in 
any part of the equipment.
• Always operate the machine on a level sur-
face. If the engine is on an incline, it could 
seize due to improper lubrication (even at the 
maximum oil level).
• Never attempt to make any adjustments 
while the engine (motor) is running (except 
where specifically recommended by the manu-
facturer).
• Protective covers must always cover rotating 
parts when the engine is running.
• Keep cooling air intake (recoil starter area) 
and muffler side of the engine at least 3 feet 
away from buildings, obstructions, and other 
combustible objects.
• Keep the engine away from flammables and 
other hazardous materials.
• Keep away from hot parts. The muffler and 
other engine parts become very hot; use cau-
tion.
• Do not touch the spark plug and ignition 
cable when starting and operating the engine.
• Check fuel hoses and joints for looseness and 
fuel leakage before each use.
• Check bolts and nuts for looseness before 
each use. A loose bolt or nut may cause serious 
engine problems.
• Always refuel outdoors. Never refuel indoors 
or in a poorly ventilated area.
• Never store the machine with fuel in the fuel 
tank inside a building where ignition sources 
are present, such as hot water and space heat-
ers, clothes dryers, and the like.
• If the fuel tank has to be drained, do this out-
doors.
• To reduce the risk of fire and burn injury, 
handle fuel with care. It is highly flammable.
• Do not smoke while handling fuel.
• Add fuel before starting the engine. Never 
remove the cap of the fuel tank or add fuel 
while the engine is running or when the en-
gine is hot.
• Loosen fuel cap slowly to release pressure 
and to keep fuel from escaping around the 
cap.
• Replace all fuel tank and container caps se-
curely.

• Wipe spilled fuel from the unit. Move 30 
feet away from refueling site before starting 
engine.
• If fuel is spilled, do not attempt to start the 
engine but move the machine away from the 
area of spillage and avoid creating any source 
of ignition until fuel vapors have dissipated.
• Never attempt to burn off spilled fuel under 
any circumstances.
• Before storing, allow the engine to cool.
• Store fuel in a cool, well-ventilated area, 
safely away from spark and/or flame-produc-
ing equipment.
• Store fuel in containers specifically designed 
for this purpose.
• Empty fuel tank and restrain the unit from 
moving before transporting in a vehicle.
• Make sure minimum clearance of 3 feet is 
maintained from combustible materials.
SERVICE
• When servicing a product, use only identical 
replacement parts. Follow instructions in the 
Maintenance section of this manual. Use of 
unauthorized parts or failure to follow Main-
tenance instructions may create a risk of injury.
• Service must be performed only by qualified 
repair personnel. Service or maintenance per-
formed by unqualified personnel may result in 
a risk of injury.
• Disconnect the spark plug wire, open drain 
valve to decompress tanks and allow water to 
drain, and allow air compressor to become cool 
to the touch before servicing. Turn pressure 
regulator knob fully clockwise after shutting 
off air compressor.

SPECIFIC SAFETY RULES FOR 

AIR COMPRESSOR

 

IMPORTANT !

Only use the air compressor for the specified 
purpose. Do not alter or modify the unit with 
respect to its original design and operation.
INTAKE AIR. Can contain carbon monoxide or 
other contaminants. Will cause serious injury 
or death. URREA air compressors are not de-
signed, intended or approved for breathing air.
Compressed air should not be used for breath-
ing air applications unless treated in accor-
dance with all applicable codes and regula-
tions.

Summary of Contents for COMP9100A

























Reviews: