background image

15

E N G L I S H •

User's Manual

conditions:  a) Start and run the generator 
outdoors. Do not operate the generator in 
a closed area, even when the doors or win-
dows are open; avoid areas where exhaust 
gases can be enclosed, such as wells, gara-
ges, basements, excavations and galleries.

• 

These generators are designed to offer a 
safe and reliable service if operated accor-
ding to the instructions. Read and unders-
tand the user’s manual before operating 
the generator.

• 

You can help prevent accidents by being 
familiar with generator controls, and fo-
llowing safe operating procedures.

RESPONSIBILITY OF THE USER

• 

Know how to stop the generator quickly in 
case of emergency.

• 

Understand the use of all generator con-
trols, outlet receptacles and connections.

• 

Make sure that anyone who operates the 
generator receives proper instruction.

• 

Do not allow children to operate the gene-
rator without parental supervision.

HAZARDS OF CARBON MONOXIDE

• 

Exhaust gases contain poisonous carbon 
monoxide, a colorless and odorless gas. 
Breathing carbon monoxide can cause loss 
of consciousness and can cause death.

• 

If you use the generator in an area that is 
confined, or even partially enclosed area, 
the air you breathe could contain a dange-
rous amount of exhaust gases.

• 

Never operate the generator inside a gara-
ge, house or near open windows or doors.

RISKS OF ELECTRICAL SHOCK

• 

The generator produces enough electrical 
power to cause a serious shock or electro-
cution if misused.

• 

The use of a generator or electrical device 
in conditions of rain, snow, or near a pool 
or sprinkler system, or if your hands are 
wet, could result in electric shock. Keep the 
generator dry.

• 

If the generator is stored outdoors, 
without protection against the weather, 
check all electrical components in the pa-
nel of control before each use. Humidity or 
ice can cause a malfunction or short circuit 
in electrical components that could result 
in electrocution.

• 

Do not connect it to an electrical system 
in a building unless an isolation switch has 
been installed by a qualified electrician.

• 

Use only an approved parallel operation 
kit (optional equipment) to connect two 
generators for parallel operation.

• 

Never connect different models and types 
of generators.

FIRE OR BURN HAZARD

• 

The exhaust system heats up enough to ig-
nite some materials.

• 

Keep the generator at least 3 feet (1 me-
ter) away from buildings and other equip-
ment during operation.

• 

Do not enclose the generator in any struc-
ture.

• 

Keep flammable materials away from the 
generator.

• 

The muffler becomes very hot during ope-
ration and remains hot for a while after 
the engine has been turned off. Be careful 
to not touch it.

• 

The silencer while it is hot. Let the engine 
cool down before storing the generator 
indoors.

• 

Gasoline is extremely flammable and ex-
plosive under some conditions. Do not 
smoke or allow flames or sparks in which 
the generator fills the tank or where gaso-
line is stored. Fill the tank in a well-ventila-
ted place with the engine stopped.

• 

Fuel vapors are highly flammable and can 
ignite after the engine has started. Make 
sure that fuel spills have been removed be-
fore starting the generator.

DEFINING TOTAL WATTAGE

In order to prevent overloading and posible da-
mage to your generator it is necessary to know 
total wattage of the connected load.
To determine which load and or appliances your 
generator will run follow these steps; 
Check wattage requirements by referring to the 
loads nameplate or by calculating it (multiply 
amps x volts = watts).
You can get help for calculation using the Table 
1 Total the watts for each item. If the nameplate
only give volts and amps, multiply volts x amps =
watts. 1 kW = 1,000 watts.
Motorized appliances or tools require more 
than their rated wattage for start up.
NOTE: Allow 2 ½ to 4 times the listed wattage 
for starting equipment powered by electric mo-

Summary of Contents for GG835A

































Reviews: