11
E N G L I S H •
User’s manual
IMPORTANT: This appliance is not intended
for use by persons (including children) with re-
duced physical, sensory or mental capabilities
may be different or reduced, or lack of experi-
ence or knowledge, unless such persons are su-
pervised or trained to operate the product by
a person responsible for their safety. Children
should be supervised to ensure they do not use
the devices as toys.
TOOL USE AND CARE
Do not force the power tool. Use the correct
tool for the application. The correct tool will
do the job better and more safely at the rate
that it was designed to work at.
Do not use tools if switch does not turn it on
or off. Any tool that cannot be controlled with
the switch is dangerous and must be repaired.
Disconnect the plug from the power source
before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and differential switch
when you are using an electric equipment.
SERVICE
Tool service must be performed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.
SPECIFIC SAFETY RULES FOR
PENDULUM JIG SAWS
1. Secure the workpiece. A workpiece held
tightly with a clamping device or bench vice is
more secure than if held with your hand.
2. Only use undamaged, flawless saw blades.
Bent or dull saw blades can break or cause a
backlash.
3. Guide the electric power tool against the
workpiece only when turned on. Otherwise,
there exists the danger of a backlash if the in-
sertion tool gets caught in the work piece.
4. Keep your hands away from the saw area.
Do not hold the workpiece from underneath.
There is danger of injury from contact with the
saw blade.
5. Hold the power tool only by the insulated
gripping surfaces when performing an opera-
tion where the cutting tool may contact hid-
den wiring or its own power cord.
6. Make sure that the saw foot stays secure
during sawing. A twisted saw blade can break
or lead to backlash.
7. Turn the electric power tool off after the
end of the work process, and then pull the
saw blade out of the cut when it has come to
a standstill. This way, you avoid a backlash and
can safely put the electric power tool away.
8. After switching the power tool off, do not
stop the saw blade by putting pressure on its
side. The saw blade can become damaged,
break, or cause a backlash. Wait until the elec-
tric power tool comes to a standstill before
putting it away.
9. While working, always use a stable underly-
ing, such as a saw table underneath small or
thin workpieces.
10. Radiation is emitted from the aperture.
Avoid skin or eye exposure to the laser beam.
Do not look into the laser beam or point it at
other persons.
SK904 manual.indd 11
08/12/15 3:57 p.m.
