US Conec Loose Fiber Ribbonizing Tool Applications Engineering Notes Download | Manualshive

Page: 3 / 10

background image

Document Title: Operating Instructions for the US Conec

Loose Fiber Ribbonizing Tool

Document Number: AEN-1408 Rev 2.0

3 of 10

3.2.1

3.2.2 Clean all tool surfaces of contaminants with 99.8% pure isopropyl alcohol

and lint free wipes. Pay particular attention to the fiber tray.

3.2.2

Fiber

Stacker

Fiber Shim

Fiber Tray

«
1
2
3
4
5
...
»

Summary of Contents for Loose Fiber Ribbonizing Tool











Reviews:

No comments

Related manuals for Loose Fiber Ribbonizing Tool

Brand: Hammer Pages: 40

Brand: National Flooring Equipment Pages: 14

Brand: N.KO Pages: 13

Brand: OMCN Pages: 13

Brand: WABCO Pages: 24

Brand: Camo Pages: 7

Brand: Tarmo Pages: 3

Brand: Greenlee Pages: 12

Brand: Major tech Pages: 16

Brand: Stihl Pages: 20

Brand: Image Industries Pages: 32

Brand: Campbell Hausfeld Pages: 4

Brand: TREND Pages: 14

Brand: Weidmüller Pages: 34

Brand: X-FLOC Pages: 51

Brand: JCM GLOBAL Pages: 32

Brand: Gardena Pages: 28

Brand: Auplex Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands