USA Measurements US-4011 User And Technical Manual Download

Page: 32 / 42

US-4011

7.3.

Display and Set Time

7.3.1.

After entering

SETUP

mode (by press down

HOLD/SETUP

key more than 3s), using

keys to select

MISC-TIME

item, press

TARE/PRESET

to display current time.

7.3.2.

Time display Format is: xx:xx:xx(hh-mm-ss) , 24h format.

7.3.3.

Press down

UNIT/DATA

more than 3s to enter modification time mode. Using

keys to modify

current time. If time of no operation is more than 5s, it will automatically exit modification mode.

7.3.4.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode

7.4.

Display and Set Date

7.4.1.

After entering

SETUP

mode (by press down

HOLD/SETUP

key more than 3s), using

keys to select

MISC-DATE

item, press

TARE/PRESET

to display current time.

7.4.2.

Date display Format is: xx.xx.xx(yy-mm-dd).

7.4.3.

Press down

UNIT/DATA

more than 3s to enter modification date mode. Using

keys to modify

current date. If time of no operation is more than 5s, it will automatically exit modification mode.

7.4.4.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode

7.5.

Display Firmware Version

7.5.1.

Press down

HOLD/SETUP

key until

CONFIG

is shown, using

keys to select

MISC-VER

item, press

TARE/PRESET

to display current Version.

7.5.2.

Firmware Version display Format is:

xx.yy, xx is hardware version, yy is software version

7.5.3.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode

7.6.

Display Test

7.6.1.

Press down

HOLD/SETUP

key until

CONFIG

is shown, using

keys to select

TEST-DSP.TST

item, press

TARE/PRESET

to enter test display mode and all segments will be lighted first.

7.6.2.

In this mode, every pressing of

ACC/TOTAL

key will light next segment, every pressing of

UNIT/DATA

key will light

next digit, press

PRINT/FUNC

key will automatically light all segments and all digits.

7.6.3.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode.

7.7.

Keyboard and Buzzer Test

7.7.1.

Press down

HOLD/SETUP

key until

CONFIG

is shown, using

keys to select

TEST-key.tst

item, press

TARE/PRESET

to enter test keypad mode, and

key

. -- will be displayed.

7.7.2.

In this mode, press a key, the value of this key will be displayed on -- position and buzzer will beep whatever

USER-BEEP-KEY

item is set.

7.7.3.

Press

HOLD/SETUP

key to return to last menu item, press

ZERO/ON/OFF

key to prepare to exit this mode

7.8.

Serial Port1/2 (COM1/2) Receiving Test

7.8.1.

Before test the receiving function of

COM1

COM2

, a cable is need to connect a PC and this indicator, and a

software be similar with Super Terminal of Windows is also need to run on PC to send bytes to this indicator.

Summary of Contents for US-4011











































Search results

Summary of Contents for US-4011

Reviews:

Related manuals for US-4011

Brands by name

Popular brands

USA Measurements US-4011, User And Technical Manual

Search results

Summary of Contents for US-4011

Reviews:

Related manuals for US-4011

Brands by name

Popular brands