Utax CD 1435 User Manual Download

Page: 153 / 250

Setup and Registration

6-5

Press the

System Menu

key.

Press [FAX], [Next] of

Transmission

, and then

[Next] of

FAX

When you register the Local FAX Number, go to
next step. When you register the Local FAX ID, go
to step 6.

Local FAX Number Entry

Press [Change] of

Local FAX Number 1

Local

FAX Number 2

If you have already registered a number, the
current registered number is displayed.

Using the numeric keys, enter the local number to
register.

•

Up to 20 digits can be entered.

•

Press [Space] to enter a space.

•

Use [ ] or [ ] to move the cursor.

•

Pressing [Backspace] deletes the character
to the left of the cursor.

Press [OK].

Local FAX ID Entry

Press [Change] of

Local FAX ID

The entry screen is displayed.

Using the numeric keys or [+]/[-], enter the four-digit
Local FAX ID number to register.

Press [OK].

Press [Close].

FAX - Local FAX Number 1

Use the numeric keys to enter a number.

Cancel

123456789

Backspace

Space

10/10/2010 10:10

Status

FAX - Local FAX ID

Set local FAX ID.

Use [-]/[+] or the numeric keys to enter a number.

Cancel

10/10/2010 10:10

(0000 - 9999)

Summary of Contents for CD 1435



























































































































































































































































Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands

Utax CD 1435, User Manual

Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands