Utax CD 1435 User Manual Download

Page: 75 / 250

FAX Operation (Advanced)

4-7

Select the check boxes beside the
destinations to select from the list.
To use an LDAP address book, select [Ext
Address Book] in [Destination].

Press [OK].

Select the destination from the One-touch keys

Press all the One-touch keys to which necessary
destinations are registered.

NOTE:

For details of the Address Book, refer to

Selecting a Destination from the Address Book on
page 3-16

. For details of the One-touch keys, refer to

Using One-touch Keys on page 2-14

You can select destinations using a combination of
direct entry, the Address Book and One-touch keys.

After selecting all the destinations, press the

Start

key. Transmission begins.

NOTE:

When

is selected in

Dest. Check before

Send

, a destination confirmation screen is displayed

when you press the

Start

key. For details, refer to

Confirmation Screen of Destinations on page 5-12

Sending using I-FAX Address

NOTE:

For more information on sending an Internet FAX (i-FAX), refer to

i-FAX Transmission on page 8-8

Press the

Send

key.

Place the originals.

Select the destination.

Enter the i-FAX address

Press [i-FAX Address Entry].

Press [i-FAX Address], enter the i-FAX
address and then press [OK].

•

Entry Check for New Destination

Off

, press

[OK] to complete entering the number.

•

Entry Check for New Destination

, press

[OK] and you are prompted to confirm the i-FAX
number is correct. Re-enter the same i-FAX
number and press [OK] to complete the entry.

Summary of Contents for CD 1435



























































































































































































































































Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands

Utax CD 1435, User Manual

Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands