Utax CD 1435 User Manual Download

Page: 76 / 250

FAX Operation (Advanced)

4-8

For details, refer to

Entry Check for New

Destination

in the machine’s

Operation Guide

To continue entering a new address, press [i-FAX
Address Entry] and repeat the above procedure.

To correct the i-FAX number, press [Detail/Edit].

After entering all the destinations, press [OK].

Select the destination from the Address Book

Press [Address Book].

Select the check boxes beside the
destinations to select from the list.
To use an LDAP address book, select [Ext
Address Book] in [Destination].

Press [OK].

Select the destination from the One-touch keys

Press all the One-touch keys to which necessary
destinations are registered.

NOTE:

For details of the Address Book, refer to

Selecting a Destination from the Address Book on
page 3-16

. For details of the One-touch keys, refer to

Using One-touch Keys on page 2-14

You can select destinations using a combination of
direct entry, the Address Book and One-touch keys.

After selecting all the destinations, press the

Start

key. Transmission begins.

NOTE:

When

is selected in

Destination Check

before Send

, a destination confirmation screen is

displayed when you press the

Start

key. For details, refer

Confirmation Screen of Destinations on page 5-12

Summary of Contents for CD 1435



























































































































































































































































Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands

Utax CD 1435, User Manual

Search results

Summary of Contents for CD 1435

Reviews:

Related manuals for CD 1435

Brands by name

Popular brands