Utax P-4531DN Operation Manual Download

Page: 108 / 352

Operation Panel

4-30

Paper Settings

This sets the paper size and type for the MP tray and cassettes from which paper is supplied.

The options available in Paper Settings are as follows:

• MP Tray Set. (MP tray settings)...4-30
• Cassette (1 to 5) Set. (Settings for the cassettes)...4-32
• Bulk Feeder Set. (Settings for the optional bulk paper feeder)...4-37
• Media Type Set. (Paper type settings)...4-39
• Reset Type Adj. (Resets customized settings)...4-42
• Paper Setup Msg(Check setting when loading paper)...4-43

Press

[Menu]

Press





to select

Paper Settings

Press

[OK]

. The

Paper Settings

menu appears showing a list of

available options.

MP Tray Set. (MP tray settings)

To print correctly on paper supplied from the MP tray, use the procedure below to set the paper size and media type.

The options available in MP Tray Set. menu are as follows:

• Paper Size (Paper size setting for the MP tray)...4-30
• Media Type (Paper type setting for the MP tray)...4-31

Paper Size (Paper size setting for the MP tray)

You can use this to set the paper size that can be supplied from the MP tray.

For more information about the paper sizes that you can feed from the MP tray, refer to

Minimum and Maximum Paper

Sizes on page A-12

In the

Paper Settings

menu, press





to select

MP Tray

Set.

Press

[OK]

. The

MP Tray Set.

menu screen appears.

Press





to select

Paper Size

Paper Settings:

MP Tray Set.

Exit

Cassette 1 Set.

Media Type Set.

Note

Feeding the paper having a paper size which does not match the current paper size from the MP tray can

cause paper jam.

MP Tray Set.:

Exit

Media Type

Paper Size

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands