Utax P-4531DN Operation Manual Download

Page: 200 / 352

Operation Panel

4-122

Enter the Login Password using the numeric keys then press

[OK]

The log in screen reappears.

Pressing

[Login]

(

[Right Select]

). If the entered Login User Name

and Login Password are correct, the

Security

menu screen

appears.

Network Security (Network security setting)

Use this procedure to specify the security settings for each of the network protocols used.

The options available in Network Security are as follows:

• SSL Setting (SSL Server setting)...4-123

In the

Security

menu, press





to select

Network

Security

Press

[OK]

. The

Network Security

menu screen appears.

6000

Note

The initial setting for the administrator's Login

Password is set as shown below.

P-4531DN: 4500

P-5031DN: 5000

P-5531DN: 5500

P-6031DN: 6000

For details on entering characters, refer to

Character Entry

Method on page A-2

Security:

Security Level

Exit

I/F Block Set.

Network Security

IMPORTANT

Check with your network administrator when selecting network settings.

Network Security:

Exit

SSL Setting

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands