Utax P-4531DN Operation Manual Download

Page: 255 / 352

5-21

Document Box

Job Box

IMPORTANT

To use the Job Box, an optional SSD must be installed in the printer. The RAM disk may also be used in the

Proof-and-Hold and Private Print modes.

Job Box is a print function that makes the Job Retention function possible. The settings are specified from the printer driver.
Refer to

Computer Settings (Printer Driver) on page 5-30

or the

Printing System Driver User Guide

Job Retention

Job Retention has four modes as summarized below. These modes are selected from the printer driver through the
application software:

Note

When using the RAM disk to use Job Box, set the RAM disk mode to On..

Quick Copy

Proof-and-Hold

Private Print

Stored Job

Primary function

To later print
additional copies

To proof the first copy
before printing
multiple copies

To hold the document
in printer to prevent
unauthorized access

To electronically store
documents such as
fax cover pages

Start storing by

Printer driver

On terminating print
setting from
application software

Prints simultaneously

Prints one copy
simultaneously

Does not print

Retrieved by

Operation panel

Default number of
copies printed at
retrieval

Same as storing
(can be changed)

One less
(can be changed)

Same as storing
(can be changed)

One
(can be changed)

Maximum number of
jobs stored

†

Jobs in excess will cause the earlier ones to be deleted.

300

Depends on the SSD
capacity (the job is
automatically deleted
after printing)

Depends on the SSD
capacity

PIN security

Yes

Yes (if necessary)

Data after printing

Stored

Deleted

Stored

Data at power off

Deleted

Stored

SSD

Necessary

Unnecessary
(RAM disk may also
be used)

Necessary

Note

Refer to the

Printing System Driver User Guide

for the driver settings and print (save) procedures.

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands