Utax P-4531DN Operation Manual Download | Manualshive

Page: 298 / 352

background image

Troubleshooting

8-14

A paper jam has occurred. The location of the paper jam is indicated in place of
the

#

’s. For details, refer to

Clearing Paper Jams on page 8-18

There is no paper cassette in the feeder, or the cassette is not inserted properly.
After reinserting the corresponding paper cassette, you should be able to print.
When two or more optional feeders are installed and the lowest one is selected,
the same message will appear if any of the upper paper feeder and the printer
cassette is improperly installed.

A RAM disk error has occurred. Look at the error code given in place of

##

.

The possible error codes and their descriptions are as follows.
02: RAM Disk Mode is set to

Off

. Set the setting to

On

Mode (Setting the RAM disk) on page 4-100

.

03: The RAM disk is write protected using command operation. Remove the
write protection using the command.
04: No disk space. Purge unnecessary files or increase the RAM disk size. For
more information, refer to

RAM Disk Size (RAM disk size setting) on page 4-

.

05: The desired file does not exist in the RAM disk. Stored the file in the RAM
disk.
10: The file stored in the RAM disk is write protected using command operation.
Remove the write protection using the command.

The machine is under the adjustment to maintain its quality. Please wait.

There are already 100 accounts registered so it is not possible to register any
new accounts.

Replace Maintenance Kit which is displayed on the message display. Contact
your Service Representative.

Message

Corrective Action

Paper jammed
##########

[ Help ]

Paper path error.
Set Cassette #.

RAM disk error.
Press [OK].

##

Refreshing drum...
Please wait.

Registered numbers
exceeded.
Cannot add.

Replace MK.

«
...
296
297
298
299
300
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

PowerShot S330 Digital ELPH

Brand: Canon Pages: 2

PowerShot S400 Digital Elph

Brand: Canon Pages: 271

Brand: Canon Pages: 6

PowerShot S330 Digital ELPH

Brand: Canon Pages: 25

Aficio MP C6503SP

Brand: Ricoh Pages: 264

Brand: BIXOLON Pages: 29

Brand: Oce Pages: 340

Brand: Muratec Pages: 112

TELEIOS GRANDE G5

Brand: d.gen Pages: 14

Brand: QMS Pages: 180

Brand: Printronix Pages: 5

Brand: Oki Pages: 2

Brand: Ricoh Pages: 2

Brand: Oakton Pages: 8

Brand: Star Micronics Pages: 194

Brand: Pantum Pages: 155

Brand: Tektronix Pages: 178

Brand: Olivetti Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands