Utax P-4531DN Operation Manual Download

Page: 308 / 352

Troubleshooting

8-24

Rear Unit

Paper is jammed in the rear cover . Remove the jammed paper using the procedure given below.

If paper is not completely ejected into the top tray, open the rear
cover.

Open the fuser cover and remove the jammed paper by pulling it out.

Close the rear cover.

IMPORTANT

If the optional Faceup Output Tray is installed,

remove it before opening the rear cover.

Note

If you cannot find a paper jam, try checking inside the

rear of the printer.

CAUTION

The fuser unit inside the printer is hot. Do

not touch it with your hands as it may result in burn
injury. Remove jammed paper carefully.

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands