Utax P-4531DN Operation Manual Download | Manualshive

Page: 331 / 352

background image

A-19

Appendix

Thick Paper

Fan the stack of paper and align the edges before loading them in the MP tray. Some types of paper have rough edges on
the back (those are created when the paper is cut). In this case, put the paper on a flat place and rub the edges once or
twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams.

Colored Paper

Colored paper should satisfy the same conditions as white bond paper, refer to

Paper Specifications on page A-11

addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to
200 °C or 392 °F).

Preprinted Paper

Preprinted paper should satisfy the same conditions as white bond paper, refer to

Paper Specifications on page A-11

. The

preprinted ink must be able to withstand the heat of fusing during the printing process, and must not be affected by silicone
oil. Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars.

Recycled Paper

Select recycled paper that meets the same specifications as the white bond paper except for whiteness, refer to

Specifications on page A-11

.

Note

If the paper jams even after you smooth it out, load the

paper in the

MP tray

with the leading edge rose up a few

millimeters as shown in the illustration.

Note

Before purchasing recycled paper, test a sample on the machine and check that the printing quality is

satisfactory.

«
...
329
330
331
332
333
...
»

Summary of Contents for P-4531DN

































































































































































































































































































































































Reviews:

No comments

Related manuals for P-4531DN

Brand: DataCard Pages: 2

Brand: Oki Pages: 16

Brand: Olivetti Pages: 179

Brand: Olivetti Pages: 36

Brand: Oki Pages: 679

Brand: Oki Pages: 40

Brand: OKIDATA Pages: 308

Brand: OKIDATA Pages: 9

Brand: OKIDATA Pages: 2

Microline 8480 FB

Brand: Oki Pages: 12

Brand: Oki Pages: 24

Brand: Ricoh Pages: 140

Brand: Inno3D Pages: 23

Brand: Parkside Pages: 176

Brand: Xerox Pages: 70

Brand: Xerox Pages: 2

Brand: Citizen Pages: 57

Brand: E-Pos Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands