Utax P-4531DN Operation Manual Download

Page: 41 / 352

2-19

Preparation before Use

Finish the installation.

When

Your software is ready to use

appears, you can use the

software. To print a test page, click the

Print a test page

checkbox

and select the machine.
Click

Finish

to exit the wizard.

If a system restart message appears, restart the computer by
following the screen prompts. This completes the printer driver
installation procedure.

Custom Install

The following procedure is an example for installing the software in Windows 8.1 using

Custom Install

Insert the

Product Library

disk.

Click

View License Agreement

and read the License Agreement.

Click

Accept

Select

Custom Install

tab.

Select the device to be installed, and click the arrow button to move
it to the

Products to Install

list.

Note

When you have selected

Device settings

in Windows

XP, the dialog box for device setting will appear after

Finish

clicked. Configure the settings for options installed on the
machine. Device settings can be configured after the
installation is completed.

For more information, refer to the

Printing System Driver User

Guide

Note

Installation on Windows must be done by a user logged

on with administrator privileges.

If the

Welcome to the Found New Hardware Wizard

dialog

box displays, select

Cancel

If the autorun screen is displayed, click

Run setup.exe

If the user account management window appears, click

Yes

(

Allow

IMPORTANT

If Wi-Fi or Wi-Fi Direct is enabled, be sure to

specify the IP address for the port name.

Installation may fail if the host name is specified.

Note

The machine cannot be detected unless it is on. If the

computer fails to detect the machine, verify that it is
connected to the computer via a network or USB cable and
that it is turned on and click

(Reload).

If the desired device does not appear, select

Add custom

device

to directly select the device.

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands