Utax P-4531DN Operation Manual Download

Page: 53 / 352

2-31

Preparation before Use

Launch your Web browser.

In the address or location bar, enter the machine's IP address or the
host name.

The factory default setting for the default user with administrator
privileges is shown below.
Login User Name:

Admin

* Upper case and lower case letters are distinguished (case

sensitive).

From the

Network Settings

menu, click

Protocol

Set

SMTP (E-mail TX)

in the

Send Protocols

From the

Function Settings

menu, click

E-mail

Note

Print the status page to check the machine's IP

address and the host name. For details, refer to

Status Page

(Printing a printer's status page) on page 4-12

Summary of Contents for P-4531DN

































































































































































































































































































































































Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands

Utax P-4531DN, Operation Manual

Search results

Summary of Contents for P-4531DN

Reviews:

Related manuals for P-4531DN

Brands by name

Popular brands